Revision as of 09:03, 3 July 2024

M1X Connecting Power and Devices

Introduction

Remote Control

Initial Setup

Connecting Power and Devices

Using the Projector

Operation

On-Screen Display Menu Tree

On-Screen Display Menu Options

Specifications

Regulatory and Service Information

Safety Precautions

Glossary

Troubleshooting

Maintenance

Connecting to Power

DC Power (Power Outlet)

Connect the power cord to the power adapter.
Connect the power adapter to the DC IN jack at the side of the projector.
Connect the power cord plug to a power outlet. When connected, the status LED will turn white.

Note: Charge the projector for 4.5 hours via the power adapter before using it in battery mode for the first time

IMPORTANT

Use only the bundled power adapter to change the battery pack and supply power to your LED projector.
Make sure your LED projector is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your LED projector in power adapter mode.
The socket outlet must be easily accessible and near your LED projector.
To disconnect your LED projector from its main power supply, unplug your LED projector from the power socket.

Power by Power Bank

The projector can also be powered by a power bank.

Connect one end of the USB Type-C cable to the USB-C port of the projector.
Connect the other end of the USB Type-C cable to the power bank.

Note:

The power bank should be 45W (15V/3A) at least, and support Power Delivery (PD) protocol output. Additionally, at 15V/3A the projector can be powered on and charge simultaneously.
Due to the IC protection mechanism, the USB-C charging function may stop briefly then continue later on.

Using the Battery

The battery level icon will show at the top right of the Home Screen. As the battery’s power level runs low, the screen will show a “low battery message”.

Battery Usage Time Information

Charging	About 4.5 hours (Power Off)
Usage Hours	Up to 4 hours (Battery Saving) Up to 2.5 hours (Eco) Up to 2 hours (Full)
Battery Level Indicator (Charging)	During Charging: Flashing White LED light Full Charge: Solid White LED light

Connecting to External Devices

HDMI Connection

Connect one end of an HDMI cable to the HDMI port of your video device. Then connect the other end of the cable to the HDMI port (supports HDCP 1.4/HDMI 1.4) of your projector.

USB Connection

USB Type A Connection
To enjoy photos, music, and movies, simply plug in a USB flash drive to the USB Type A port.

USB-C Connection
Connect one end of a USB Type C cable to the USB-C port of your device. Then connect the other end of the cable to the USB-C port of your projector.

NOTE:

Ensure your USB Type C device can support video transmission.

The connected device can also be charged (5V/2A).

microSD

To enjoy photos, music, and movies, simply plug in a microSD to the Micro SD slot.

NOTE: Only supports FAT32 format and up to 64 GB.

@@ Line 13: / Line 13: @@
 }}
 </noinclude>
 =Connecting to Power=
 ==DC Power (Power Outlet)==
@@ Line 34: / Line 35: @@
 :*The socket outlet must be easily accessible and near your LED projector.
 :*To disconnect your LED projector from its main power supply, unplug your LED projector from the power socket.
-</div>
@@ Line 58: / Line 59: @@
 |-
 |'''Charging'''
-|About 4.5 hours
+|About 4.5 hours (Power Off)
 |-
 |'''Usage Hours'''
-|up to 6 hours (Battery Saving)/up to 4 hours (Extended Eco)/up to 3 hours (ECO) /up to 2.5 hours (Full)
+|Up to 4 hours (Battery Saving)
+Up to 2.5 hours (Eco)
+Up to 2 hours (Full)
 |-
 |'''Battery Level Indicator (Charging)'''

M1X Connecting Power and Devices: Difference between revisions