• Print Print

XG271QG Initial Setup: Difference between revisions

From ViewSonic Documentation
Jump to: navigation, search
Newer edit →
Created page with "<noinclude> {{Sticky_Menu |1=XG271QG_Introduction |2=XG271QG_Initial_Setup |3=XG271QG_Connecting_Power_and_Devices |4=XG271QG_Adjusting_the_Viewing_Angle |5=XG271QG_Quick_Menu..."
 
Line 28: Line 28:
</gallery>
</gallery>
{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}}
{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}}
=Installing and Removing the Elite Hood=
# Prepare both pieces of the Elite Hood as well as a screwdriver.
# Ensure the hood pieces are in the correct orientation.
# Line up each screw of the Elite Hood piece with the screw holes on the side of the monitor.
# Carefully attach the Elite Hood to the monitor, making sure not to over-tighten the screws.
# To remove the Elite Hood, reverse the previous steps.
<gallery widths=200px heights=200px mode="nolines">
XG270QG_Hood_Install_1.png| Correct orientation
XG270QG_Hood_Install_2.png| Carefully attach
</gallery>


=Wall Mounting=
=Wall Mounting=

Revision as of 08:52, 7 January 2022

XG271QG Initial Setup
Introduction
Initial Setup
Connecting Power and Devices
Adjusting the Viewing Angle
Quick Menu
Hot Keys
On-Screen Display Menu Operation
On-Screen Display Menu Tree
On-Screen Display Menu Options
Advanced Features and Settings
Specifications
Regulatory and Service Information
Safety Precautions
Glossary
Troubleshooting
Maintenance

Stand Installation

  1. Place the monitor on a flat, stable surface with the screen facing down.
  2. Align and connect the two (2) points on the monitor stand’s base with the monitor stand’s neck.
  3. Use the captured screw in the monitor stand’s base and secure it to the monitor stand’s neck.
  4. Align and slide the upper hooks of the monitor stand into the stand mounting slots as shown in the illustration.
  5. Using the stand’s handle, lift the device into its upright position on a flat, stable surface.
  • Align the base with the neck
    Align the base with the neck
  • Align the hooks
    Align the hooks
  • Lift into an upright position
    Lift into an upright position
Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.

Wall Mounting

Refer to the table below for the standard dimensions for wall mount kits.

For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.
Maximum Loading Hole Pattern (W x H) Interface Pad (W x H x D) Pad Hole Screw Specification & Quantity
14 kg 100 x 100 mm 115 x 115 x 2.6 mm Ø 5 mm M4 x 10 mm - 4 pieces
  1. Turn off the device and disconnect all cables.
  2. Place the device on a flat, stable surface with the screen facing down.
  3. Pull down slightly to disengage the hooks. Then remove the stand.
  4. Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm).
  5. Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall.
  • Disengage the hooks
    Disengage the hooks
  • VESA mounting points
    VESA mounting points

Using the Security Slot

Retrieved from "https://manuals.viewsonic.com/index.php?title=XG271QG_Initial_Setup&oldid=17039"