![Print](INVALID-TITLE:<span style="margin-right:10px;"></span><span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|1px|link=http://localhost/stage/tango/index.php?title=XG270QG_Initial_Setup&printable=yes]]</span></span>
<span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|30px|link=http://localhost/stage/tango/index.php?title=XG270QG_Initial_Setup&printable=yes]]</span></span>
[[Category:Template]]
[[Category:Archive]]){kind=small}
XG270QG Initial Setup: Difference between revisions
From ViewSonic Documentation
No edit summary |
|||
| Line 27: | Line 27: | ||
{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | {{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | ||
=Installing and Removing the Elite Hood | =Installing and Removing the Elite Hood= | ||
# Prepare both pieces of the Elite Hood as well as a screwdriver. | |||
# Ensure the hood pieces are in the correct orientation. | |||
# Line up each screw of the Elite Hood piece with the screw holes on the side of the monitor. | |||
# Carefully attach the Elite Hood to the monitor, making sure not to over-tighten the screws. | |||
# To remove the Elite Hood, reverse the previous steps. | |||
<gallery widths=200px heights=200px mode="nolines"> | |||
XG270QG_Hood_Install_1.png| Correct orientation | |||
XG270QG_Hood_Install_2.png| Carefully attach | |||
</gallery> | |||
=Wall Mounting= | =Wall Mounting= | ||
| Line 56: | Line 65: | ||
<gallery widths=200px heights=200px mode="nolines"> | <gallery widths=200px heights=200px mode="nolines"> | ||
XG270QG_Wall_Mount_1.png| | XG270QG_Wall_Mount_1.png| Disengage the hooks | ||
XG270QG_Wall_Mount_2.png| | XG270QG_Wall_Mount_2.png| VESA mounting points | ||
</gallery> | </gallery> | ||
[[Category:XG270QG]] | [[Category:XG270QG]] | ||
Revision as of 09:36, 21 April 2020
Stand Installation
- Place the monitor on a flat, stable surface with the screen facing down.
- Align and connect the two (2) points on the monitor stand’s base with the monitor stand’s neck.
- Use the captured screw in the monitor stand’s base and secure it to the monitor stand’s neck.
- Align and slide the upper hooks of the monitor stand into the stand mounting slots as shown in the illustration.
- Using the stand’s handle, lift the device into its upright position on a flat, stable surface.
-
Align the base with the neck -
Align the hooks -
Lift into an upright position
Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.
Installing and Removing the Elite Hood
- Prepare both pieces of the Elite Hood as well as a screwdriver.
- Ensure the hood pieces are in the correct orientation.
- Line up each screw of the Elite Hood piece with the screw holes on the side of the monitor.
- Carefully attach the Elite Hood to the monitor, making sure not to over-tighten the screws.
- To remove the Elite Hood, reverse the previous steps.
-
Correct orientation -
Carefully attach
Wall Mounting
Refer to the table below for the standard dimensions for wall mount kits.
For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.
| Maximum Loading | Hole Pattern (W x H) | Interface Pad (W x H x D) | Pad Hole | Screw Specification & Quantity |
|---|---|---|---|---|
| 14 kg | 100 x 100 mm | 115 x 115 x 2.6 mm | Ø 5 mm | M4 x 10 mm - 4 pieces |
- Turn off the device and disconnect all cables.
- Place the device on a flat, stable surface with the screen facing down.
- Pull down slightly to disengage the hooks. Then remove the stand.
- Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm).
- Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall.
-
Disengage the hooks -
VESA mounting points
