![Print](INVALID-TITLE:<span style="margin-right:10px;"></span><span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|1px|link=http://localhost/stage/tango/index.php?title=XG270QG_Initial_Setup&printable=yes]]</span></span>
<span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|30px|link=http://localhost/stage/tango/index.php?title=XG270QG_Initial_Setup&printable=yes]]</span></span>
[[Category:Template]]
[[Category:Archive]]){kind=small}
XG270QG Initial Setup: Difference between revisions
From ViewSonic Documentation
Created page with "{{Sticky_Menu |1=XG270QG_Introduction |2=XG270QG_Initial_Setup |3=XG270QG_Making_Connections |4=XG270QG_Adjusting_the_Viewing_Angle |5=XG270QG_Quick_Menu |6=XG270QG_Hot_Keys |..." |
|||
| Line 21: | Line 21: | ||
<gallery widths=200px heights=200px mode="nolines"> | <gallery widths=200px heights=200px mode="nolines"> | ||
XG270QG_Install_1.png| | XG270QG_Install_1.png| Align the base with the neck | ||
XG270QG_Install_2.png| | XG270QG_Install_2.png| Align the hooks | ||
XG270QG_Install_3.png| | XG270QG_Install_3.png| Lift into an upright position | ||
</gallery> | </gallery> | ||
{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | {{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | ||
=Installing and Removing the Elite Hood | |||
=Wall Mounting= | |||
Refer to the table below for the standard dimensions for wall mount kits. | |||
{{Note-yellow|For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.}} | |||
{| class="wikitable" style="background-color:#f0eeea; text-align:center;" | |||
! Maximum Loading | |||
! Hole Pattern (W x H) | |||
! Interface Pad (W x H x D) | |||
! Pad Hole | |||
! Screw Specification & Quantity | |||
|- | |||
|14 kg | |||
|100 x 100 mm | |||
|115 x 115 x 2.6 mm | |||
|Ø 5 mm | |||
|M4 x 10 mm - 4 pieces | |||
|} | |||
# Turn off the device and disconnect all cables. | |||
# Place the device on a flat, stable surface with the screen facing down. | |||
# Pull down slightly to disengage the hooks. Then remove the stand. | |||
# Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm). | |||
# Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall. | |||
<gallery widths=200px heights=200px mode="nolines"> | |||
XG270QG_Wall_Mount_1.png| <translate>Disengage the hooks</translate> | |||
XG270QG_Wall_Mount_2.png| <translate>VESA mounting points</translate> | |||
</gallery> | |||
[[Category:XG270QG]] | [[Category:XG270QG]] | ||
Revision as of 09:29, 21 April 2020
Stand Installation
- Place the monitor on a flat, stable surface with the screen facing down.
- Align and connect the two (2) points on the monitor stand’s base with the monitor stand’s neck.
- Use the captured screw in the monitor stand’s base and secure it to the monitor stand’s neck.
- Align and slide the upper hooks of the monitor stand into the stand mounting slots as shown in the illustration.
- Using the stand’s handle, lift the device into its upright position on a flat, stable surface.
-
Align the base with the neck -
Align the hooks -
Lift into an upright position
Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.
=Installing and Removing the Elite Hood
Wall Mounting
Refer to the table below for the standard dimensions for wall mount kits.
For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.
| Maximum Loading | Hole Pattern (W x H) | Interface Pad (W x H x D) | Pad Hole | Screw Specification & Quantity |
|---|---|---|---|---|
| 14 kg | 100 x 100 mm | 115 x 115 x 2.6 mm | Ø 5 mm | M4 x 10 mm - 4 pieces |
- Turn off the device and disconnect all cables.
- Place the device on a flat, stable surface with the screen facing down.
- Pull down slightly to disengage the hooks. Then remove the stand.
- Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm).
- Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall.
-
Disengage the hooks -
VESA mounting points
