LD163-181 Installation

From ViewSonic User Guide Database
Jump to navigation Jump to search
Backtotop.svg

Before Installation

  1. Maintain an adequate air gap between the back of the display and any wall for proper ventilation.
  2. Ensure there is no direct airflow from air conditioning or heating vents blowing on the display.
  3. Avoid installing the display in places with high humidity.
  4. Due to high power usage, always use power cords specifically designed for this product.

Wall Mounting

Installing the Upper and Lower Mounting Brackets

    LD Wall Mounting Bracket.svg
  1. Ensure the wall area and size is an appropriate installation site.
  2. Using the Wall Mount Bracket (pictured above) as a guide, mark each of the eight (8) holes and pre-drill each.
  3. Install the first Upper Wall Mount Bracket with the provided screws (M6x50mm Expansion for masonry; TA6x30mm for load bearing wood).
  4. Repeat Step 2, ensuring the second Upper Wall Mount Bracket is level with the first upper bracket.

  5. LD Wall Mounting After Upper Brackets.svg

  6. Install the Lower Wall Mount Brackets in the same manner as the Upper Wall Mount Brackets. The distance between the Upper and Lower Wall Mount Brackets is 77-3/8" (1965 mm).

  7. LD Wall Mounting Spacing.svg

    Ensure the wall can safely support 423.29 lbs. (192 kg).
    NOTE: You can also install the Upper Wall Mount Brackets, hang the screen, and then install the Lower Wall Mount Brackets for a more precise fit.
  8. After installing both Upper and Lower Wall Mount Brackets, the installation wall should look like:

  9. LD Brackets.svg

Installing the Middle Cabinets

  1. Ensure the Mounting Brackets on the rear of the four (4) Middle Cabinets are positioned at the top and bottom mounting positions as shown below:

  2. LD Rear Middle Panels Separate Original.svg

  3. Carefully lift each Middle Cabinet up onto the Upper Wall Mount Brackets.

  4. LD Wall Mounting After Middle Screens Update.svg

  5. Ensure the Mounting Brackets sit securely on the Wall Mount Brackets as shown below.

  6. LD Wall Mount Close Up.svg

  7. Push each Locking Bolt and lock each Hook with the hex tool to securely connect each cabinet together.

  8. LD Wall Mounting Connecting Middle Screens.png

    NOTE: There are six (6) Locking Bolts and 12 Hooks between each cabinet.
  9. Lift the remaining Middle Cabinets up onto the Upper Wall Mount Brackets, ensuring the Mounting Brackets sit securely on the Wall Mount Brackets.
  10. Repeat Step 4, securing the cabinets together with each Locking Bolt and Hook.

  11. LD Wall Mounting After Middle Screens.svg

Installing the Left and Right Cabinet

  1. Ensure the Mounting Brackets on the rear of the Left and Right Cabinet are positioned at the top and bottom mounting positions as shown below:

  2. LD Rear Left and Right.svg

  3. Carefully lift the Left and Right Cabinet up onto the Upper Wall Mount Brackets, ensuring the Mounting Brackets sit securely on the Wall Mount Brackets.

  4. LD163-181 Wall Mounting After All Screens.svg

  5. If necessary, adjust the Left or Right Cabinet so that they fit seamlessly with the Middle Cabinets.
  6. Push each Locking Bolt and lock each Hook with the hex tool to securely connect the Left and Right Cabinets.

  7. LD163-181 Wall Mounting Locking Bolts.png
    NOTE: There are six (6) Locking Bolts and 12 Hooks between each cabinet.

Connecting the System Control Box

  1. Carefully unfold the System Control Box panel. Ensure the main system control board is on the left.
  2. NOTE: Use caution as the System Control Box panel will be separated into two pieces, however the wires are connected.
  3. Align the holes of the Cabinet with the System Control Box to attach.

  4. LD163-181 Wall Mounting Connecting Box.svg

  5. Further secure the System Control Box to the Cabinets with the 24 provided screws (M6x16mm).

  6. LD Box Install.png

  7. Connect the Network and Power cables of the Cabinets to the System Control Box.
  8. NOTE: There are six (6) Network and six (6) Power cables to connect.

    LD163-181 Wall Mounting Connecting Net Pow.svg

Installing the LED Modules

Install each LED Module onto the Cabinets, being sure to match the corresponding numbers on the Module to the Cabinet.

Please wear Anti-Static Gloves before installing the LED modules.


LD163-181 Wall Mounting Modules 1.svg

Ensure each Module is flush and that there is little to no gap between each.

LD163-181 Wall Mounting Modules No Cover.svg

Installing System Control Box Covers

There are three (3) System Control Box Covers: Left, Middle, and Right.

LD Control Box Covers.svg
  1. Begin by installing the Right Cover onto the System Control Box.
  2. NOTE: Ensure the Power Button cable is connected to the System Control Box Power cable before securing the Cover.
  3. After connecting the Power Button cable, ensure the Right Cover is properly aligned with the System Control Box; then secure it with the 15 provided screws (KM3x6mm).
  4. LD Wall Mounting Right Cover.svg
  5. Repeat the above steps for the Middle and Left Cover.
    LD Wall Mounting All Covers Yes LED.svg
  6. Your display is now ready for use.
  7. LD Front Panel.svg

Floor Stand Installation

The floor stand is an optional accessory. Follow the below instructions to install your LED Display onto the stand.

Component List

Letter Item Quantity Description
A
LD Floor Stand Hex Tool.svg
1 Hex Tool
B
LD Floor Stand Bolt.svg
8 M6 x 80mm Bolt
C
LD Floor Stand Left Support.svg
1 Left Support
D
LD Floor Stand Bottom Beam.svg
1 Bottom Cross Beam
E
LD Floor Stand Right Support.svg
1 Right Support
F
LD Floor Stand Top Beam.svg
1 Top Cross Beam

Dimensions

LD163-181 Floor Stand Dimensions.svg

Constructing the Floor Stand

Constructing the Floor Stand
  1. Connect the Left Support to the Bottom Cross Beam with two (2) M6 x 80mm bolts.
  2. Connect the Right Support with the Bottom Cross Beam with two (2) M6 x 80mm bolts.
  3. Connect the Top Cross Beam to the Left and Right Supports with four (4) M6 x 80mm bolts.
  4. NOTE: Ensure the groove of the Top Cross Beam faces inwards.
  5. Ensure all bolts are tightened properly.

Connecting the System Control Box to the Floor Stand

  1. Carefully unfold the System Control Box panel. Ensure the main system control board is on the left.
  2. NOTE: Use caution as the System Control Box panel will be separated into two pieces, however the wires are connected.
  3. Align the System Control Box to the eight (8) holes on the Bottom Cross Beam and secure it with eight (8) screws (M6x10mm).
  4. LD Floor Stand Connecting the System Control Box.png
  5. Install two (2) additional screws (M6x10mm) to connect the two halves of the System Control Box.
  6. LD Floor Stand Connecting the System Control Box 1.png

Installing the Middle Cabinets

  1. Ensure the four (4) Mounting Brackets on the rear of the four (4) Middle Cabinets are positioned as shown below:
  2. Carefully lift a Cabinet up onto the Floor Stand, securing the Mounting Bracket into the support channel of the Top Cross Beam. The bottom of the Cabinet will rest on the Bottom Cross Beam.
  3. Secure the Cabinet to the Support with the provided screws (M6x10mm).
  4. Push each Locking Bolt and lock each Hook with the hex tool to securely connect each cabinet together.
  5. NOTE: There are six (6) Locking Bolts and 12 Hooks between each cabinet.
  6. Repeat Steps 2~4 for the remaining Middle Cabinets.

Installing the Left and Right Cabinet

Connect the Network and Power Cables

Installing the LED Modules

Installing System Control Box Covers