IFP55G1 Using Your ViewBoard

Powering ON/OFF your ViewBoard

1. Ensure the power cord is connected, plugged into a power outlet, and the Power Switch is in the “ON” position.
   

   Note: The AC Power input and Power Switch are located at the bottom of the display.

2. Press the Power button to turn ON the ViewBoard.
   

3. To turn the ViewBoard OFF, press and hold the Power button.

On-Screen Display (OSD) Menu Tree

Main Menu	Sub-menu	Menu Option
VGA	H Position	(-/+, 0~100)
	V Position	(-/+, 0~100)
	Clock	(-/+, 0~100)
	Clock Phase	(-/+, 0~100)
	Zoom Mode	Full
		Normal (4:3)
		Real (1:1)
		Dynamic (16:9)
		21:9
	Auto Adjust	OK
	Screen Reset	Cancel
		Reset
Input Source	VGA
	HDMI 1
	HDMI 2
	HDMI 3
	PC
	Type-C
WriteAway	Off
	Except PC (OPS)
	No Signal Input Only
	Black Board Mode (Auto Signal Detection: Off)
Picture	Picture Mode	Normal
		Dynamic
		Soft
		User
	Contrast	(-/+, 0~100)
	Brightness	(-/+, 0~100)
	Color	(-/+, 0~100)
	Tint	(-/+, 0~100)
	Sharpness	(-/+, 0~100)
	Color Temperature	Warm (7500K)
		Normal (9300K)
		Cool (10000K)
		User
	Noise Reduction	Off
		Low
		Medium
		High
	Overscan	off
		On
	RGB Range	Full Range
		Limited Range
		Auto
	Flicker Free	Off
		On
	Blue Light Filter	(-/+, 0~100)
	Gamma Set	Native
		2.2
		2.4
	Backlight	(-/+, 0~100)
	Picture Reset	Cancel
		Reset
Audio	Volume Control	Speaker
		Audio Out
		Sync
	Treble	(-/+, 0~100)
	Bass	(-/+, 0~100)
	Balance	(-/+, 0~100)
	Volume	(-/+, 0~100)
	Maximum Volume	(-/+, 0~100)
	Minimum Volume	(-/+, 0~100)
	Mute	Off
		On
	Audio Out Sync	Enable
		Disable
	Audio Out Volume (Line Out)	(-/+, 0~100)
	Audio Reset	Cancel
		Reset
Time	Off Time	Off
		1 hour~24 hours
	Date and Time	Set Date
		Set Time
		Choose Time Zone
		Use 24-hour Format
	Schedule	Schedule List
		Enable
		Start Time
		End Time
		Input	HDMI 1
			HDMI 2
			HDMI 3
			PC
			Type-C
			VGA
		Dat of the Week
		Every Week
	OSD Turn Off	Off
		5/15/30/60 seconds
	Input Information	Off
		5/10/20/30/60 seconds
	Automatic Date & Time	Off
		On
	Time Reset	Cancel
		Reset
About	Display Information	Model Name
		Serial No.
		Operation Hours
		SW Version
Advanced Options	Saving	Panel Saving	Brightness	Off
				On
		Power Save	Mode 1
			Mode 2
			Mode 3
			Mode 4
		Power LED Light	Off
			On
	Boot	Boot On Source	HDMI 1
			HDMI 2
			HDMI 3
			PC
			Type-C
			VGA
		Boot On Logo	Off
			On
	Signal	Auto Signal Detection	Off
			On
		No Signal Standby	off
			0 mins
			5 mins
			15 mins
			30 mins
	Port	HDMI with One Wire	Off (default)
			On
		USB Cloning	Import
			Export
		USB Auto Play	Off
			On
	Others	Switch On State	Power Off
			Forced On
			Last Status
		WOL	Off
			On
			Monitor ID 1~98
		OSD Language
		Factory Reset	Cancel
			Reset
		Advanced Option Reset	Cancel
			Reset
Other Settings	Energy Start	Off
		On
	Light Sensor	Off
		On
	IP
	Port
Leave OSD Menu	Leave OSD Menu

On-Screen Display (OSD) Menu Operation

Access VGA, Input Source, WriteAway, Picture, Audio, Time, About, Advanced Options, and Other Settings settings through the OSD Menu.

Open the OSD Menu by pressing MENU on the remote control or the Menu button on the front Control Panel.

VGA

Note: For VGA input source only.

Item	Description
H Position	Adjust the screen image position horizontally.
V Position	Adjust the screen image position vertically.
Clock	Adjust the frequency of the pixel clock signal. This will affect the resolution and refresh rate.
Clock Phase	Adjust the clock phase to improve the display’s clarity and avoid flickering.
Zoom Mode	Select the aspect ratio of the display.
Auto Adjust	Automatically adjust the position of the screen image.
Screen Reset	Reset the Screen settings to their default settings.

Input Source

Select one of the available input sources.

WriteAway

Picture

Audio

Time

About

Advanced Options

Other Settings

Leave OSD Menu

Exit the OSD Menu.