![Print](INVALID-TITLE:<span style="margin-right:10px;"></span><span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|1px|link=http://localhost/stage/tango/index.php?title=VG2208A_Initial_Setup&printable=yes]]</span></span>
<span class="d-none d-md-inline"><span id="t-print" style="position: relative;bottom:2px; left:1%; z-index:9999; padding:0; margin:0;">[[File:Icon_Print.svg|Print|30px|link=http://localhost/stage/tango/index.php?title=VG2208A_Initial_Setup&printable=yes]]</span></span>
[[Category:Template]]
[[Category:Archive]]){kind=small}
VG2208A Initial Setup: Difference between revisions
From ViewSonic Documentation
| (4 intermediate revisions by the same user not shown) | |||
| Line 19: | Line 19: | ||
=Stand Installation= | =Stand Installation= | ||
<div class="res-img">[[File:VG2208A_Install_1.png| | <div class="res-img">[[File:VG2208A_Install_1.png|500px|alt=Stand installation process]]</div> | ||
{{Note|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | {{Note|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}} | ||
| Line 50: | Line 50: | ||
<li> | <li> | ||
<p>Remove the monitor stand.</p> | <p>Remove the monitor stand.</p> | ||
<div class="res-img">[[File:VG2208A_Wall_Mount_1.png| | <div class="res-img">[[File:VG2208A_Wall_Mount_1.png|600px|alt=monitor hook removeal]]</div> | ||
</li> | </li> | ||
<li> | <li> | ||
<p>Attach the mounting bracket to the VESA mounting holes at the rear of the device. Then secure it with four screws (M4 x 10 mm).</p> | <p>Attach the mounting bracket to the VESA mounting holes at the rear of the device. Then secure it with four screws (M4 x 10 mm).</p> | ||
<div class="res-img">[[File:VG2208A_Wall_Mount_2.png| | <div class="res-img">[[File:VG2208A_Wall_Mount_2.png|400px|alt=monitor hook removeal]]</div> | ||
</li> | </li> | ||
<li> Follow the instructions that come with the wall mounting kit to mount the monitor.</li> | <li> Follow the instructions that come with the wall mounting kit to mount the monitor.</li> | ||
Latest revision as of 06:30, 2 September 2024
Before Installing the Stand
Please follow the guidelines below when handling the monitor stand.
Note: Please make sure that the stand is firmly attached to the monitor before raising it upright, and then remove the bolt.
Stand Installation
Note: Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.
Wall Mounting
Refer to the table below for the standard dimensions for mounting kits.
Note:
- For use only with a UL certified mounting kit/bracket. To obtain a wall mounting kit or height adjustment base, contact ViewSonic® or your local dealer.
- Mounting kits are sold separately.
| Maximum Loading | Hole Pattern (W x H) |
Interface Pad (W x H x D) |
Pad Hole | Screw Specification | Screw Quantity |
|---|---|---|---|---|---|
| 14 kg | 100 x 100 mm | N/A | Ø 5 mm | M4 x 10 mm | 4 screws |
- Turn off the device and disconnect all cables.
- Place the device on a flat, stable surface with the screen facing down.
-
Remove the monitor stand.
-
Attach the mounting bracket to the VESA mounting holes at the rear of the device. Then secure it with four screws (M4 x 10 mm).
- Follow the instructions that come with the wall mounting kit to mount the monitor.
Using the Security Slot
Please see Using the Security Slot.