• Print Print

VB-PEN-007 Initial Setup: Difference between revisions

From ViewSonic Documentation
Jump to: navigation, search
← Older edit
 
(One intermediate revision by the same user not shown)
Line 16: Line 16:
{{Note|A short, 10 minute charge can provide one (1) hour of use.}}</ol>
{{Note|A short, 10 minute charge can provide one (1) hour of use.}}</ol>


=Powering On and Pairing the AirPen (VB-PEN-007)=
=Powering On and Pairing the AirPen=
<ol><li>Plug the USB Receiver into a USB Type A port of a display device.</li>
<ol><li>Plug the USB Receiver into a USB Type A port of a display device.</li>
<div class="res-img">[[File:VB-PEN-007_Plug_USB_Receiver.png|Plug in the USB Receiver|250px]]</div>
<div class="res-img">[[File:VB-PEN-007_Plug_USB_Receiver.png|Plug in the USB Receiver|250px]]</div>
Line 24: Line 24:
<li>After successfully powering on and pairing the VB-PEN-007, the LED Indicator will be a steady blue.</li></ol>
<li>After successfully powering on and pairing the VB-PEN-007, the LED Indicator will be a steady blue.</li></ol>


=Re-Pairing the AirPen (VB-PEN-007)=
=Re-Pairing the AirPen=
If the AirPen (VB-PEN-007) needs to be re-paired, please follow the steps below:
If the AirPen (VB-PEN-007) needs to be re-paired, please follow the steps below:
<ol><li>Remove the USB Receiver from the display device.</li>
<ol><li>Remove the USB Receiver from the display device.</li>

Latest revision as of 03:33, 27 September 2024

VB-PEN-007 Initial Setup
Introduction
Initial Setup
Using the Pen
Specifications
Regulatory and Service Information

Charging the AirPen

Note: Fully charge the AirPen (VB-PEN-007) before its first use.
Charging the Pen
  1. Connect the USB Type C end of the included USB cable to the Charging Port of the AirPen (VB-PEN-007).
  2. Then connect the other end, the USB Type A, of the cable to a USB Type A port of a display or other power delivering device.
  3. When charging, the LED Indicator will be a steady red. When fully charged, the VB-PEN-007 can provide four (4) hours of use.
    4. Note: A short, 10 minute charge can provide one (1) hour of use.

Powering On and Pairing the AirPen

  1. Plug the USB Receiver into a USB Type A port of a display device.
    2. Plug in the USB Receiver
  2. Press and hold the AirPen's (VB-PEN-007) Power Button for three (3) seconds to begin pairing.
    3. Note: When in pairing mode, the LED Indicator will be flashing blue.
    Press and Hold the Power Button
  3. After successfully powering on and pairing the VB-PEN-007, the LED Indicator will be a steady blue.

Re-Pairing the AirPen

If the AirPen (VB-PEN-007) needs to be re-paired, please follow the steps below:

  1. Remove the USB Receiver from the display device.
    2. Remove the USB Receiver
  2. Press and hold both the Volume Up and Volume Down buttons on the AirPen (VB-PEN-007) for three (3) seconds to enter pairing mode.
    3. Note: When in pairing mode, the LED Indicator will be flashing blue.
    Press and Hold the Volume Buttons
  3. Plug the USB Receiver into a USB Type A port of the display device.
    4. Plug the USB Receiver In
  4. When paired successfully, the LED Indicator will be a steady blue.
Retrieved from "https://manuals.viewsonic.com/index.php?title=VB-PEN-007_Initial_Setup&oldid=51501"