View source for VG2440V Initial Setup

<noinclude> {{Top}}
{{Sticky_Menu_Monitor__3.0_No_Adv
|1=VG2440V_Introduction
|2=VG2440V_Initial_Setup
|3=VG2440V_Connecting_Power_and_Devices
|4=VG2440V_Adjusting_the_Viewing_Angle
|5=VG2440V_Quick_Menu
|6=VG2440V_Hot_Keys
|7=VG2440V_On-Screen_Display_Menu
|8=VG2440V_On-Screen_Display_Menu_Tree
|9=VG2440V_On-Screen_Display_Menu_Options
|10=VG2440V_Specifications
|11=VG2440V_Regulatory_and_Service_Information
}}
</noinclude>
=Stand Installation=
# Place the box on a flat, stable surface and open the front flap of the box to reveal the contents. Remove the top tray.
# Remove the monitor stand’s base and neck. Align and connect the three (3) points on the monitor stand’s base with the monitor stand’s neck.
# Use the captured screw in the monitor stand’s base and secure it to the monitor stand’s neck.
# Align and slide the upper hooks of the monitor stand into the stand mounting slots. Ensure the stand is secure and the quick release tab positively clicks into place.
# Using the stand’s handle, lift the device out of the box and into its upright position on a flat, stable surface.

<gallery mode="traditional" heights=200px widths=200px>
VG2440V_Stand_Install_01.svg|Align and connect the base and neck
VG2440V_Stand_Install_02.svg|Align the upper hooks
VG2440V_Stand_Install_03.svg|Ensure the quick release tab clicks into place
VG2440V_Front_View_No_ID.svg|Lift into an upright position
</gallery>
:{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}}

=Wall Mounting=
Refer to the table below for the standard dimensions for wall mount kits.

:{{Note-yellow|For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.}}

{| class="wikitable" style="text-align: center;" 
! style="background-color:#c41230; color:#ffffff;" | Maximum Loading
! style="background-color:#c41230; color:#ffffff;" | Hole Pattern (W x H)
! style="background-color:#c41230; color:#ffffff;" | Interface Pad (W x H x D)
! style="background-color:#c41230; color:#ffffff;" | Pad Hole
! style="background-color:#c41230; color:#ffffff;" | Screw Specification & Quantity
|-
|14 kg
|100 x 100 mm
|115 x 115 x 2.6 mm
|Ø 5 mm
|M4 x 10 mm - 4 pieces
|}

# Turn off the device and disconnect all cables.
# Place the device on a flat, stable surface with the screen facing down.
# Press and hold the quick release tab and carefully lift the stand.
# Pull down slightly to disengage the hooks. Then remove the stand.
# Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm).
# Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall.

<gallery widths=200px heights=200px mode="traditional">
VG2440V_Wall_Mounting_01.svg| Press and hold the quick release tab
VG2440V_Wall_Mounting_02.svg| Disengage the hooks
VG2440V_Wall_Mounting_03.svg| VESA mounting points
</gallery>

=Using the Webcam=
:'''NOTE:''' To activate the webcam, ensure the monitor is connected to your computer via the USB Upstream port.
<div class="res-img">[[File:VG2440V_USB-B_to_A.svg]]</div>
===Opening and Covering the Webcam===
<gallery mode="nolines" heights=300px widths=300px>
File:VG2440V_Webcam_Open.svg| Opened
File:VG2440V_Webcam_Close.svg| Covered
</gallery>

===Tilting the Webcam===
Tilt the slider door forwards or backwards to adjust the viewing angle (-5° to 5°).
<div class="res-img">[[File:VG2440V_Webcam_Tilt.png|250px]]</div>

<noinclude>=[[Monitor_Security_Slot| Using the Security Slot]]=</noinclude>

[[Category:VG2440V]]