View source for X10-4K Remote Control

=Overview=
[[File:X10-4K_Remote_Control.png|thumb|120px| Remote Control]]

{| class="wikitable" width=45% style="text-align: center";
! style="font-weight:bold; background-color:#c41230; color:#ffffff;" | Button
! style="text-align: center; font-weight:bold; background-color:#c41230; color:#ffffff;" | Icon
! style="text-align: center; font-weight:bold; background-color:#c41230; color:#ffffff;" | Description
|-
| style="font-weight:bold;" | Power
| [[File:X10_Power_Icon.png|50px]]
| Turns the projector On or Off.
|-
| style="font-weight:bold;" | Source
| [[File:X10_Source_Icon.png|50px]]
| Displays the input source selection bar.
|-
| style="font-weight:bold;" | Focus
| [[File:X10_Focus_Icon.png|50px]]
| Automatically focus the image.
To manually adjust, press and hold the Focus button on the remote control for three (3) seconds.
|-
| style="font-weight:bold;" | Setting
| [[File:X10_Setting_Icon.png|50px]]
| Displays the Settings menu.
|-
| style="font-weight:bold;" | Audio Mode
| [[File:X10_Audio_Icon.png|50px]]
| Displays the speaker settings.
|-
| style="font-weight:bold;" | Bluetooth
| [[File:X10_BT_Icon.png|50px]]
| View Bluetooth options.
|-
| style="font-weight:bold;" | Up/Down/Left/Right
| rowspan="2" | [[File:X10_Wheel_Icon.png|50px]]
| rowspan="2" | Navigates and selects the desired menu items and makes adjustments.
|-
| style="font-weight:bold;" | Shuttle Wheel Left/Right
|-
| style="font-weight:bold;" | OK
| [[File:X10_Ok_Icon.png|50px]]
| Confirms the selection.
|-
| style="font-weight:bold;" | Return
| [[File:X10_Return_Icon.png|50px]]
| Returns to the previous screen.
|-
| style="font-weight:bold;" | Home
| [[File:X10_Home_Icon.png|50px]]
| Access the Home menu.
|-
| style="font-weight:bold;" | Volume Control
| [[File:X10_Volume_Icon.png|50px]]
| Increases/decreases the volume level or mutes/unmutes it.
|}

=Effective Range=
[[File:X10_remote_range.png|thumb|200px| IR Receiver Location]]
To ensure proper function of the remote control follow the steps below:
# The remote control must be held at an angle within 30° perpendicular to the projector’s IR remote control sensor(s).
# The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.)

::<small>'''NOTE:''' Refer to the illustration for the location of the infrared (IR) remote control sensor(s).</small>

=Replacing the Batteries=
# Remove the battery cover from the bottom of the remote control by pressing the finger grip and sliding it across.
# Remove any existing batteries (if necessary) and install two AAA batteries.
# Replace the battery cover by aligning it with the base and pushing it back into position.
::<div class="res-img">[[File:X10_Remote_Battery.png|600px| ]]</div>
{{Note-yellow| '''NOTE:'''
:* Avoid leaving the remote control and batteries in excessive heat or a humid environment.
:* Replace only with the same or equivalent type recommended by the battery manufacturer.
:* If the battery is drained or if you will not be using the remote control for an extended period of time, remove the battery to avoid damage to the remote control.
:* Dispose of used batteries according to the manufacturer’s instructions and local environment regulations for your region.}}

[[Category:X10-4K]]
[[Category:X Series]]