VG2708A

From ViewSonic Documentation
(Redirected from VG2708A Full Guide)
Jump to: navigation, search

Introduction

Package Contents

  • Monitor
  • Power cord
  • Quick start guide
  • Video cable
Note: The cables included in your package may vary depending on your country or region. Please contact your local reseller for more information.

Product Overview

Front View

Front of the monitor on its stand, with the Control Panel Keys at the lower right of the bezel.

Rear View

Rear of the monitor showing the stand attached at the center and the I/O ports along the bottom edge.

I/O Ports

I/O ports panel, numbered 1 to 7: DisplayPort, HDMI, VGA, Audio Out, USB Upstream, USB Downstream, and AC IN.
The I/O ports of the monitor.
# Description
1 DisplayPort
2 HDMI
3 VGA
4 Audio Out
5 USB Upstream
6 USB Downstream
7 AC IN

Initial Setup

Installing the Stand

1

Attaching the stand to the rear of the monitor, which is lying screen-down, and fastening the base to the stand with its thumbscrew.

2

Rear of the monitor standing upright on its assembled stand, with a callout showing the stand lock pin being pulled up.

3

The monitor standing upright on its stand, seen from the front.

Caution: Place the monitor on a flat, stable surface to ensure safety and optimal performance.

Removing the Stand

1

Rear of the monitor on its stand before the stand is removed.

2

The monitor lying screen-down: the base is loosened from the stand, and the stand is lifted off the rear of the monitor.

Caution: Before removing the stand, turn off the monitor, disconnect all cables, and place the monitor on a flat, stable surface with the screen facing down.

Mounting the Monitor

After removing the stand, the monitor can be mounted using an optional mounting kit.

Rear of the monitor showing the four VESA mounting holes 100 mm apart horizontally and vertically.
The standard dimensions and loading of mounting kits.
Maximum Loading Hole Pattern (W × H) Screw Specification Screw Quantity
14 kg 100 × 100 mm M4 × 10 mm 4
  1. Attach the mounting bracket to the VESA mounting holes at the rear of the monitor, securing it with screws.
  2. Follow the mounting kit instructions to mount the monitor.
Note: For use only with a UL certified mounting kit/bracket. To obtain a wall mounting kit or height adjustment base, contact ViewSonic® or your local dealer.

Using the Security Slot

A security cable locked into the security slot on the rear of the monitor and looped around a table leg.

To prevent theft and minimize damage, use a security slot locking device to secure the monitor to a fixed object.

Additionally, fastening the monitor to a wall or fixed object using a security cable can help support the weight of the monitor in order to prevent the monitor from falling over.

Making Connections

Connecting to Power

The power cord connected to the AC IN port on the rear of the monitor and plugged into a power outlet.


Connecting to External Devices

DisplayPort, HDMI, VGA, and USB cables connecting the monitor to a computer, and an audio cable from Audio Out to headphones or speakers.


Using the Monitor

Adjusting the Viewing Angle

Height Adjustment

Lower or raise the monitor to the desired height (0 to 130 mm).

The monitor screen raised to its highest position on the stand.
Note: When adjusting, press down firmly along the adjustment track holding the monitor with both hands on the side.

Screen Orientation Adjustment (Pivot)

1

The monitor raised to its highest position on the stand.

2

The monitor rotated 90 degrees clockwise or counterclockwise from landscape to portrait orientation.

  1. Raise the monitor height to its maximum height and then tilt it back fully.
  2. Rotate the monitor 90 degrees clockwise or counterclockwise from landscape to portrait orientation.
Note:
  • When adjusting, hold the monitor firmly on both sides.
  • To rotate the screen, change the system’s display orientation settings.

Swivel Angle Adjustment

Swivel the monitor to the left or right for the desired viewing angle (360°).

Top view of the monitor swiveling left and right on its stand base.


Tilt Angle Adjustment

Tilt the monitor forwards or backwards to the desired viewing angle (−3.5° to 28°).

Side view of the monitor tilting forwards and backwards on its stand.
Note: To adjust the monitor, support the stand with one hand and gently tilt the screen with the other.

Turning the Monitor On/Off

Note: Even when turned off, the monitor will still consume power when plugged in. Unplug the power cord when not in use for extended periods.
Front of the monitor with a hand pressing the Power button at the lower right of the bezel.
  1. Make sure the monitor is connected to power.
  2. Press the Power button to turn on the monitor.
  3. To turn the monitor off, press the Power button again.
Note: If the On-Screen Display Menu is still on screen, press and hold the Power button for three seconds to turn off the monitor.

Using the Control Panel Keys

Use the Control Panel Keys to access the Quick Menu, activate Hot Keys, navigate the On-Screen Display Menu, and change settings.

Close-up of the Control Panel Keys under the bottom bezel, labeled 1 (star), 2, 3, 4, and 5 (Power).

Quick Menu

Press the 1 key to activate the Quick Menu.

Quick Menu open on View Mode, listing Standard, Game, Movie, Web, Text, MAC, and Mono.
Note: Follow the key guide that appears on the screen to select the option or make adjustments.
The Quick Menu options.
Menu Description
ViewMode Sets a preset display option.
Volume Adjusts the volume level.
Contrast/Brightness Adjusts the contrast or brightness level.
Input Select Sets the input source.
Exit Closes the Quick Menu.

Configuring the Settings

General Operations

On-Screen Display Menu open, showing the main menu list.

Press the 2/3/4 key to open the On-Screen Display Menu.

On-Screen Display Menu with a main menu selected and its options shown.

Press the 1 or 2 key to select the main menu. Then press the 3 key to open the selected menu.

On-Screen Display Menu with a menu option selected and its sub-menu open.

Press the 1 or 2 key to select a menu option. Then press the 3 key to open the sub-menu.

On-Screen Display Menu with a setting being adjusted in the sub-menu.

Press the 1 or 2 key to adjust values or select an option. Then press the 3 key to confirm.
Note:
  • Certain menu option adjustments do not require the user to press the 3 key to confirm the selection. Follow the key guide that appears on the bottom of the screen to select the option or make adjustments.
  • Press the 4 key to return to the previous menu. To exit the On-Screen Display Menu, press the 5 (Power) key.

On-Screen Display (OSD) Menu Tree

Input Select

Input Select menu options.
Menu Option
D-Sub · HDMI · DisplayPort

Audio Adjust

Audio Adjust menu options.
Sub-menu Menu Option
Volume 0–100

ViewMode

ViewMode menu options.
Menu Option
Standard · Game · Movie · Web · Text · MAC · Mono

Color Adjust

Color Adjust menu options.
Sub-menu Menu Option
Contrast/Brightness Contrast 0–100
Brightness 0–100
Color Temperature sRGB · Bluish · Cool · Native · Warm
User Color Red 0–100
Green 0–100
Blue 0–100
Color Space
(for DP & HDMI only)
Auto · RGB · YUV
Color Range
(for DP & HDMI only)
Auto · Full Range · Limited Range

Manual Image Adjust

Manual Image Adjust menu options.
Sub-menu Menu Option
Auto Image Adjust
(for D-Sub only)
—
Horizontal Size
(for D-Sub only)
0–100
H./V. Position
(for D-Sub only)
Horizontal Position 0–100
Vertical Position 0–100
Fine Tune
(for D-Sub only)
0–100
Sharpness 0–100/25
Aspect Ratio 4:3 · 5:4 · 16:9 · 16:10
Overscan
(for DP & HDMI only)
On · Off
Black Stabilization 0–100/10
Advanced DCR 0–100/25
Response Time Standard · Advanced · Ultra Fast

Setup Menu

Setup Menu options.
Sub-menu Menu Option
Language English · Français · Deutsch · Español · Italiano · Suomi · Svenska · Русский · Türkçe · Česká · Tiếng Việt · 日本語 · 한국어 · 繁體中文 · 简体中文
Variable Refresh Rate
(for DP & HDMI only)
On · Off
Information —
OSD Size Native · Large
OSD Timeout 5 · 15 · 30 · 60
OSD Background On · Off
Power Indicator On · Off
Auto Power Off On · Off
USB Charging On · Off
Sleep 30 minutes · 45 minutes · 60 minutes · 120 minutes · Off
ECO Mode Standard · Optimize · Conserve
DisplayPort 1.1 On · Off
Auto Detect On · Off
DDC/CI On · Off
Memory Recall —
Note: Memory Recall is the default display configuration and settings, and it’s the setting required for ENERGY STAR® qualification. Modifying these default settings can increase energy consumption beyond the ENERGY STAR® limits. ENERGY STAR® is a program jointly administered by the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy, which promotes energy-efficient products and practices to help save money and protect the environment.
ENERGY STAR logo.

Appendix

Specifications

The monitor's technical specifications.
Category Specification Value
Display Type IPS, Color a-Si TFT Active Matrix 1920 × 1080 LCD; 0.3114 (H) mm × 0.3114 (V) mm pixel pitch
Display Size 68.58 cm / 27 in. (viewable)
Color Filter RGB Vertical Stripe
Glass Surface Anti-Glare (Haze 25%), Hard Coating (3H)
Input Signal Frequency D-Sub fh: 24–86 kHz;
fv: 48–75 Hz
DisplayPort fh: 30–115 kHz;
fv: 48–100 Hz
HDMI fh: 30–115 kHz;
fv: 48–100 Hz
Version DisplayPort 1.2
HDMI 1.4
Compatibility PC up to 1920 × 1080
Macintosh up to 1920 × 1080
Resolution and Timings[1] Preset 1920 × 1080 @ 60 Hz
Supported
  • 1920 × 1080 @ 50, 60, 75, 100 Hz
  • 1680 × 1050 @ 60 Hz
  • 1600 × 1200 @ 60 Hz
  • 1600 × 900 @ 60 Hz
  • 1440 × 900 @ 60, 75 Hz
  • 1440 × 576 @ 50 Hz
  • 1400 × 1050 @ 60, 75 Hz
  • 1366 × 768 @ 60 Hz
  • 1360 × 768 @ 60 Hz
  • 1280 × 1024 @ 50, 60, 75 Hz
  • 1280 × 960 @ 50, 60, 75 Hz
  • 1280 × 800 @ 60, 75 Hz
  • 1280 × 768 @ 50, 60, 75 Hz
  • 1280 × 720 @ 50, 60 Hz
  • 1152 × 900 @ 66 Hz
  • 1152 × 870 @ 75 Hz
  • 1152 × 864 @ 60, 75 Hz
  • 1024 × 768 @ 50, 60, 70, 72, 75 Hz
  • 1024 × 600 @ 60 Hz
  • 848 × 480 @ 60 Hz
  • 832 × 624 @ 75 Hz
  • 800 × 600 @ 56, 60, 72, 75 Hz
  • 720 × 576 @ 50 Hz
  • 720 × 480 @ 60 Hz
  • 720 × 400 @ 70 Hz
  • 640 × 480 @ 50, 60, 67, 73, 75 Hz
  • 640 × 400 @ 60, 70 Hz
  • 640 × 350 @ 70 Hz
Power[2] Input Voltage AC 100–240V, 50/60 Hz (auto switch)
Display Area Active Size (H × V) 597.888 × 336.312 mm
23.54 × 13.24 in.
Operating Conditions Altitude 5 km (16,404.2 ft)
Relative Humidity 20% to 90% (non-condensing)
Temperature 0° C to 40° C
32° F to 104° F
Storage Conditions Altitude 12.1 km (39,698.2 ft)
Relative Humidity 5% to 90% (non-condensing)
Temperature -20° C to 60° C
-4° F to 140° F
Dimensions (with stand) Physical (W × H × D) 615 × 537.38 × 223 mm
24.21 × 21.16 × 8.78 in.
Weight (with stand) Physical 6.1 kg (13.4 lb)
Wall Mount Dimensions 100 × 100 mm
Power Consumption On[3] 19W (Typical) without audio
21W (Typical) with 50% audio
Off ≤ 0.3 W (Maximum)
  1. ↑ Do not set the graphics card in your computer to exceed these timing modes; doing so may result in permanent damage to the display.
  2. ↑ Please use the power adapter/power cord from ViewSonic® or an authorized source only.
  3. ↑ The test condition follows EEI standards.

Hot Keys

When the On-Screen Display Menu is off, you can quickly access special functions by using the Control Panel Keys.

Shortcut keys and their function.
Key Description
1 + 2 Press and hold the keys to lock/unlock the On-Screen Display Menu. When the menu appears on the screen, continue holding both keys for 10 seconds. If the On-Screen Display Menu is locked, a message appears on the screen.
2 + 3 Press and hold the keys to lock/unlock the Power button. When the menu appears on the screen, continue holding both keys for 10 seconds. If the Power button is locked, a message appears on the screen.
3 + 4 Press the keys to display/hide the Boot up Screen or Message OSD when the monitor is turned on.

Regulatory and Service Information

Compliance Information

This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

CAN ICES (B) / NMB (B)

CE Conformity for European Countries

CE logo

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

The following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

WEEE logo

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below.

RoHS2 restricted substances and concentration limits.
Substance Proposed Maximum Concentration Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Bis (2-ethylhexyl) phthalate (DEHP) 0.1% < 0.1%
Butyl benzyl phthalate (BBP) 0.1% < 0.1%
Dibutyl phthalate (DBP) 0.1% < 0.1%
Diisobutyl phthalate (DIBP) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below. Examples of exempted components are:

  • Copper alloy containing up to 4% lead by weight.
  • Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
  • Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
  • Lead in dielectric ceramic in capacitors for a rated voltage of 125 V AC or 250 V DC or higher.

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Product Disposal at End of Product Life

ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

For EU users, please contact us for any safety/accident issue experienced with this product:

Address.
ViewSonic Europe Limited
Flevolaan 38, 1382JZ, Weesp,
the Netherlands
Phone.
+31 0800023299

TCO Certified

TCO Certified

Copyright Information

Copyright © 2023 ViewSonic® Corporation. All rights reserved.

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

ViewSonic® and the three birds logo are registered trademarks of ViewSonic® Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.

ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).

As an ENERGY STAR® partner, ViewSonic® Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Noto Sans Font. Copyright 2018 The Noto Project Authors. This Font Software is licensed under the SIL Open Font License, Version 1.1.

Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.

This Copyright Information may be translated into multiple languages. All translated versions are provided for reference only. In the event of any discrepancy or inconsistency among different language versions, the English version shall prevail.

Version
VG2708A_UG_ENG_1b_20260518


See Also

Customer Service

Limited Warranty

Safety Precautions

Troubleshooting

Maintenance