Features

360 degree smart stand with instant Power ON/OFF (with Lens cover function).
Auto keystone to correct distorted images automatically.
Eye Protection function for objects that get too close to the lens (30 cm distance / 30 degrees).
USB-C for video transmission and power supply.
Embedded battery for easy outdoor projection (up to 6 hours).
Adjustable light source mode to extend your battery usage hours.
16GB internal storage (Max. 12GB available).
User-friendly UI design for easy navigation.
Music mode enables users to enjoy music without projecting an image.
Short throw lens design to allow 1.6m distance to project 60” screen size.
LED light source with excellent light source life (30,000 hrs).
Supports 3D display.
Color modes providing choices for different projection purposes.
Multi-language On-Screen Display (OSD) Menus.

NOTE: The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and projection distance.

Package Contents

M1 mini Projector
Remote Control (with batteries)
Power Cord
USB-C Cable (1 m)
Power Adapter
Soft Carry Bag
Quick Start Guide

Projector Overview

Number	Item
1	Speaker
2	Ventilation
3	Focus Ring
4	Tripod Hole
5	IR Receiver
6	Eye Protection Sensor
7	Enter/Power Button
8	Volume Down
9	Volume Up
10	Return
11	Battery Indicator
12	Speaker PR
13	Micro SD
14	DC IN
15	USB-C
16	HDMI Port
17	Audio Out
18	USB Reader (5V/1A out)
19	Reset Button^[1]
20	Smart Stand

↑ In the event of a system crash, use the Reset Button to restart the projector.

Overview

Remote Control

Number	Button
1	Power
2	Settings
3	Home
4	Harman Kardon Settings
5	Music Mode^[1]
6	Up / Keystone
7	OK
8	Down / Keystone
9	Left / Backward
10	Right / Forward
11	Mute
12	Play / Pause
13	Return
14	Volume Up
15	Volume Down

↑ Blank the projection image and focus on the music.

Effective Range

To ensure proper function of the remote control follow the steps below:

The remote control must be held at an angle within 30° perpendicular to the projector’s IR remote control sensor(s).
The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.).

Replacing the Batteries

To open the battery cover, turn the remote control over to view its back, open the cover in the direction of the arrow.
Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and pushing it back down into position. Stop when it clicks into place.

NOTE:

Avoid leaving the remote control and batteries in excessive heat or a humid environment.

Replace only with the same or equivalent type recommended by the battery manufacturer.

If the battery is drained or if you will not be using the remote control for an extended period of time, remove the battery to avoid damage to the remote control.

Dispose of used batteries according to the manufacturer’s instructions and local environment regulations for your region.

Choosing a Location - Projector Orientation

Personal preference and room layout will decide the installation location. Consider the following:

Size and position of your screen.
Location of a suitable power outlet.
Location and distance between the projector and other equipment.

Front Table
Front Ceiling
Rear Table
Rear Ceiling

Location	Description
Front Table	The projector is placed near the floor in front of the screen.
Front Ceiling	The projector is suspended upside-down from the ceiling in front of the screen.
Rear Table^[1]	The projector is placed near the floor behind the screen.
Rear Ceiling^[1]	The projector is suspended upside-down from the ceiling behind the screen.

↑ ^1.0 ^1.1 A rear projection screen is required.

Projection Dimensions

16:9 Image on a 16:9 Screen

Screen Size		Image Width		Image Height		Projection Distance
inch	mm	inch	mm	inch	mm	inch	mm
24	610	21	531	12	299	25	637
30	762	26	664	15	373	31	796
40	1016	35	885	20	498	42	1062
50	1270	44	1106	25	622	52	1327
60	1524	52	1327	29	747	63	1593
70	1778	61	1549	34	871	73	1858
80	2032	70	1770	39	996	84	2124
90	2286	78	1991	44	1120	94	2389
100	2540	87	2212	49	1245	105	2655

There is a 3% tolerance among these numbers due to optical component variations. It is recommended to physically test the projection size and distance before permanently installing the projector.

Mounting the Projector

Screw a standard tripod into the screw hole on the bottom side of the projector.

NOTE: The tripod is sold separately.

Connecting to Power

Power Adapter

Connect the power cord to the power adapter.
Connect the DC power connector to your projector.
Connect the AC power cord to a power source.

NOTE: Charge the projector for 3 hours before using it in battery mode for the first time.

Use only the bundled power adapter to charge the battery pack and supply power to your LED projector.
Ensure that your LED projector is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your LED projector on power adapter mode.
The socket outlet must be easily accessible and near your LED projector.
To disconnect your LED projector from its main power supply, unplug your LED projector from the power socket.

Battery Power

The battery level icon will show at the top right of the Home Screen. As the battery’s power level runs low, the screen will show a “low battery message”.

Battery Usage Time Information

Charging	About 4.5 hours
Usage Hours	Up to 6 hours (with Battery Saving mode and without USB power supply)
Battery Level Indicator (Charging)	During Charging: Red LED light is On Full Charge: White LED light is On

NOTE: There will be a very low power consumption during Standby mode, it is suggested to fully charge the battery before usage every time.

The battery used in this device may present a risk of fire or chemical burn if removed or disassembled.
Follow the warning labels for your personal safety.
Risk of explosion if battery is replaced by an incorrect type.
Do not dispose of in fire.
Never attempt to short-circuit your LED projector’s battery.
Never attempt to dissemble and reassemble the battery.
Discontinue usage if leakage is found.
The battery and its components must be recycled or disposed of properly.
Keep the battery and other small components away from children.

Connecting to External Devices

1. Micro SD

NOTE:

SDHC (up to 32 GB).
FAT32/NTFS.

2. USB-C

NOTE:

Please use the supplied USB-C cable to make sure the compatibility.
Please make sure your USB-C device can support video transmission.

3. HDMI

NOTE: iPhone/iPad users need to buy an additional adapter. To avoid compatibility issues, please use Apple authorized accessories.

4. USB Reader

NOTE:

FAT32/NTFS.
Hard disk support up to 1 TB.

5. USB Power Supply

NOTE: 5V/1A.

Wireless Screen Mirroring

Screen Mirroring provides a wireless connection for users to mirror the screen on their personal iOS or Android smart device.

Connect to Wi-Fi
Select Screen Mirror

To use Screen Mirroring:

Open Settings, and go to: Network Settings > Wi-Fi > On.
Connect the M1+ to your wireless router. Ensure your device is connected to the same network as the projector.
On the Home Screen, select Screen Mirroring.
Once inside the Screen Mirroring menu, follow the below directions:

For iOS:

Access the drop down control menu.
Select the “Screen Mirroring” icon.
Choose “ViewSonic PJ-XXXX”.

For Android:

Download and install the “Google Home” application and open it.
Select the Account icon at the lower-right corner of the screen.
Select the “Mirror Device” function.
Choose “ViewSonic PJ-XXXX”.

NOTE: Some Android devices support direct “Casting”. If your device does, go to the Casting feature and choose “ViewSonic PJ-XXX” from the list of available devices.

Connecting to Bluetooth

Bluetooth Speaker

The projector is equipped with Bluetooth that allows the user to connect their device wirelessly for audio playback.

Select Bluetooth Speaker
Select Confirm

To connect and pair your device:

On the Home Screen, select Bluetooth Speaker and press OK.
When the dialogue box appears, select Confirm and press OK on the remote control to enter Bluetooth mode.
A sound effect will be audible upon entering pairing mode.
Upon successful connection, another sound effect will be audible.

NOTE: Additionally, you can also use the remote control to activate the Bluetooth speaker.

Connecting to Networks

Wi-Fi Connection

To connect to a Wi-Fi network:

From the Home Screen, go to: Settings > Network Settings > Wi-Fi.
Press Left or Right on the remote control to select On.
Available Wi-Fi networks will then be displayed. Select one of the available Wi-Fi networks.
If you connect to a secure Wi-Fi network, you must enter the password when prompted.

Starting the Projector

Ensure the projector is connected to a power source or that the battery has sufficient charge.
Press and hold the Power button for three (3) seconds to turn on the projector; or press the Power button on the remote control.
Move the Smart Stand to your desired viewing angle.

Adjusting the Projector's Height and Projection Angle

The projector is equipped with one (1) Smart Stand. Adjusting the stand will change the projector’s height and the vertical projection angle. Carefully adjust the stand to fine tune the projected image’s position.

NOTE: If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image can become trapezoidal. However, the “Auto Vertical Keystone” function will correct the issue automatically.

Adjusting the Focus

To adjust the image focus of the on-screen image, slowly move the focus ring upwards or downwards.

Shutting Down the Projector

Press and hold the Power button on the projector or press the Power button on the remote control.

Home Screen

The Home Screen is displayed every time you start the projector. To navigate the Home Screen, simply use the directional buttons on the remote control. You can return to the main Home Screen at any time by pressing the Home button on the remote control.

Menu	Description
HDMI	Switch to the connected HDMI source.
USB-C	Switch to the connected USB-C source.
USB Reader	Switch to the connected USB source.
Local Storage	Switch to locally stored files.
Micro SD	Switch to the connected Micro SD.
Screen Mirroring	Mirror personal iOS or Android devices.
Apps Center	View, launch, and uninstall Apps.
Bluetooth Speaker	Wireless connection for Bluetooth playback.
Wallpaper	Change the Home Screen wallpaper.
Settings	Adjust various settings.
Information	View display and projector information.

HDMI

Project content from your media player, PC, or other HDMI compatible device.

Connect your media player, PC, or other HDMI compatible device to the projector via an HDMI cable.
Using the directional buttons on the remote control select HDMI, and press OK.

USB-C

Project content from your media player, PC, or other USB-C compatible device.

Connect your media player, PC, or other USB-C compatible device to the projector via a USB-C cable.
Using the directional buttons on the remote control select USB-C, and press OK.

USB Reader

Project content from your USB Type A device.

Connect your USB Type A device to the projector via the USB Reader input.
Using the directional buttons on the remote control select USB Reader, and press OK.

Local Storage

Easily manage locally stored files and folders.

Select a single file
Select multiple files

From the Home Screen, select Local Storage.
To select a single file, use the directional buttons to select the desired file. Then press OK on the remote control to open the selected file.
To select multiple files, select Select then press the OK button. Boxes will then appear in front of each file. Use the up and down directional buttons to highlight files, and press OK to select them.
Once a file is selected, you can Copy, Paste, Cut, or Delete the file.

Micro SD

Project content from your Micro SD card.

Connect your Micro SD card to the projector via the Micro SD input.
Using the directional buttons on the remote control select Micro SD, and press OK.

Screen Mirroring

Please see Wireless Screen Mirroring

Apps Center

View, launch, and uninstall Apps.

Step 1 - Select Apps Center
Step 2 - Launch the App

To view your Apps, from the Home Screen select Apps Center.
Use the directional buttons to select the desired App. Then press OK on the remote control to launch the App.

Aptoide

The projector is pre-loaded with the Aptoide store, which allows users to download and install different Apps.

Step 1 - Select Aptoide
Step 2 - Navigate the store

Select: Home > Apps Center > Aptoide.
Use the directional buttons to navigate the menu options. When you find your preferred App, press the OK button to install it.

NOTE:

Apps not pre-loaded by ViewSonic may not be compatible or work properly.
Some Apps may require a keyboard or mouse.
Some Apps may be Region-Specific.

To Uninstall Apps

Open the Apps Center by selecting: Home > Apps Center.
Use the directional buttons to select the desired App.
Press and hold OK on the remote control for three (3) seconds.
Select OK to uninstall the App.

Bluetooth Speaker

Please see Connecting to Bluetooth

Wallpaper

Select this option to change the Home Screen wallpaper.

From the Home Screen, select Wallpaper.
Choose your preferred picture from the pre-installed wallpapers.

Settings

Under Setting you can adjust various projector settings.

Using the directional buttons on the remote control select Setting, and press OK.
Use the Up and Down buttons to select the desired setting and press OK. Then use the Left and Right buttons or the OK button to make adjustments or selections.

Information

View various details about the projector.

Media Control Bar Buttons

The Control Bar buttons will appear on screen if a video, music, or photo file are selected to be opened. Additionally, you can press OK on the remote control to show the control bar.

Tips for using USB
When using USB for reading and/or storage please keep in mind the following:

Some USB storage devices may not be compatible.
If you use an USB extension cable, the USB device may not recognize the USB.
Only use USB storage devices formatted with Windows FAT32 or NTFS file system.
Larger files will need extra time to load.
Data on USB storage devices may be damaged or lost. Back up important files.

Supported File Formats

Supported Office formats:

Supported Multimedia formats:

Firmware Upgrade

Users can update the firmware by USB.

NOTE: Do not unplug the power cord or USB during the upgrading process.

Download the latest version from the ViewSonic website and copy the file to a USB device.
Power on the projector and plug in the USB with the new Firmware.
The system will display a dialog message confirming your wish to update.
After selecting Confirm, a progress bar will appear as the update process begins.
After reaching 100% the projector will restart. The whole process will take about five (5) minutes.
After updating the Firmware, it will take a few minutes to restart the projector.

Using the 3D Function

This portable cinema features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images. If the 3D signal is input from an HDMI 1.4a compatible device, the portable cinema detects the signal for 3D Sync information and once detected, it projects images in 3D format automatically.

To activate 3D functions:

When playing videos, press OK and the video control bar will pop up.
Select the 3D settings icon, the 3D Settings menu is displayed in the right bottom corner.
Highlight 3D self detect and change to Auto.

NOTE:

When the 3D Sync function is on:

The brightness level of the projected image will decrease.
The Color Mode cannot be adjusted.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to ON to correct the problem.

On-Screen Display (OSD) Menu Tree

Source	Main Menu	Sub-menu	Options
HDMI		3D Self Detect	Manual
		3D Self Detect	Auto
		3D Conversion	None
			Side by Side
			Top and Bottom
			Frame Packing
			Frame Sequential
			Line Alternative
		3D Sync Invert	On
		3D Sync Invert	Off
		Hue	(-/+, 0~100)
		Sharpness	(-/+, 0~100)
		Saturation	(-/+, 0~100)
USB-C		3D Self Detect	Manual
		3D Self Detect	Auto
		3D Conversion	None
			Side by Side
			Top and Bottom
			Frame Packing
			Frame Sequential
			Line Alternative
		3D Sync Invert	On
		3D Sync Invert	Off
		Hue	(-/+, 0~100)
		Sharpness	(-/+, 0~100)
		Saturation	(-/+, 0~100)
USB Reader	Play	Video Control Bar	Backwards / Forwards / Fast Rewind / Fast Forward / Play / Pause / Volume / Settings
		Photo Control Bar	Backwards / Play / Forwards / Zoom In / Zoom Out / Rotate / Settings
		Music Control Bar	Backwards / Play / Forwards / Repeat / Shuffle
	Select	Copy / Paste / Cut / Delete
Local Storage	Play	Video Control Bar	Backwards / Forwards / Fast Rewind / Fast Forward / Play / Pause / Volume / Settings
		Photo Control Bar	Backwards / Play / Forwards / Zoom In / Zoom Out / Rotate / Settings
		Music Control Bar	Backwards / Play / Forwards / Repeat / Shuffle
	Select	Copy / Paste / Cut / Delete
Micro SD	Play	Video Control Bar	Backwards / Forwards / Fast Rewind / Fast Forward / Play / Pause / Volume / Settings
		Photo Control Bar	Backwards / Play / Forwards / Zoom In / Zoom Out / Rotate / Settings
		Music Control Bar	Backwards / Play / Forwards / Repeat / Shuffle
	Select	Copy / Paste / Cut / Delete
Screen Mirroring
Settings	Image Settings	Aspect Ratio	Auto
			4:3
			16:9
		Auto Keystone	On
		Auto Keystone	Off
		V Keystone	(-/+, -40~40)
		Brightness	(-/+, 0~100)
		Contrast	(-/+, -50~50)
		Projector Position	Front Table
			Rear Table
			Front Ceiling
			Rear Ceiling
	Display Mode	Brightest
		Standard
		Theater
		Music
	Harman Kardon	Mute	On
		Mute	Off
		Audio Volume	(-/+, 0~20)
		Audio Mode	Movie
			Bass Booster
			Instrumental
	Light Source Mode	Full
		Eco
		Extended Eco
		Battery Saving
	Eye Protection	On
	Eye Protection	Off
	Network Settings	Wi-Fi	On
	Network Settings	Wi-Fi	Off
	Reset Settings	Reset
	Reset Settings	Cancel
	Language	English
		French
		German
		Italian
		Spanish
		Russian
		繁體中文
		简体中文
		日本語
		한국어
		Swedish
		Dutch
		Turkish
		Czech
		Portuguese
		Thai
		Polish
		Finnish
		Arabic
		Indonesian
		Hindi
		Vietnamese
Apps Center
Bluetooth Speaker
Wallpaper
Information	Color Mode
	Light Source Mode
	Local Storage Capacity
	App Storage of Local
	Bluetooth
	Firmware Version

On-Screen Display (OSD) Menu Options

Image Setting Menu

Menu Option	Description
Aspect Ratio	The Aspect Ratio is the ratio of the image width to the image height. With the advent of digital signal processing, digital display devices, like this projector, can dynamically stretch and scale the image output to a different aspect than that of the image input signal. Auto Scales an image proportionally to fit the projector’s native resolution in its horizontal width. This is suitable for the incoming image which is neither 4:3 nor 16:9 and you want to make the most use of the screen without altering the image’s aspect ratio. 4:3 Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV, and 4:3 aspect DVD movies, as it displays them without aspect alteration. 16:9 Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV.
Auto Keystone	Provides a rectangular screen image by automatically adjusting the keystone number when there is a trapezoidal screen image caused by the tilting of the projector.
V Key Stone	Keystone can be adjusted manually from -40 to 40.
Brightness	The higher the value, the brighter the image. Lower values will result in a darker image.
Contrast	Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.
Projector Position	Select the preferred projection position.

Display Mode Menu

Menu Option	Description
Brightest	Maximizes the brightness of the projected image. This mode is suitable for environments where higher brightness is required, such as using the projector in well lit rooms.
Standard	Displays images in standard levels of contrast, brightness, and sharpness.
Theater	Optimizes the image for movies.

Audio Settings Menu

Menu Option	Description
Harman Kardon	Mute Mute or unmute the volume. Audio Volume Adjust the volume from 0 to 20. Audio Mode Movie: Default audio mode. Bass Booster: Optimized for bass heavy media. Instrumental: Optimized for non-vocal media.

Light Source Mode Settings

Menu Option	Description
Light Source Mode	Full Default mode when connecting with the power adapter. Up to 2.5 hours of playback. Eco Default mode when using the embedded battery. Up to 3 hours of playback. Extended Eco Up to 4 hours of playback. Battery Saving Up to 6 hours of playback.

Eye Protection Menu

Menu Option	Description
Eye Protection Sensor	To protect eyes from the direct light of the projector, when an object gets close to the lens (30 cm), a sensor will detect it and automatically turn off the light. On Turn on the sensor for 30 cm detection. Off Turn off the sensor.

Network Settings Menu

Menu Option	Description
Wi-Fi	Turn Wi-Fi On or Off.

Reset Settings Menu

Menu Option	Description
All Reset	Reset settings to factory default.

Language Menu

Menu Option	Description
Language	Select your desired language.

Technical Specifications

Model No.	P/N
VS17337	M1+

Item	Category	Specifications
Projector	Type	0.2” WVGA, DLP
	Display Size	24”~100”
	Brightness	250 LED Lumens
	Throw Distance	38” @ 1m
	Throw Ratio	1.2
	Lens	F=1.7, f=5.5 mm
	Optical Zoom	Fixed
	Lamp Type	RGB LED
	Light Source Life (Normal)	up to 30,000 hours
	Display Color	1.07 Billion Colors
	Keystone
	Local Storage	Total: 16 GB; Available: 12 GB
	Audible Noise (Eco)	25dB
Input Signal	HDMI	fh: 15h~135KHz, fv:23~120Hz
Resolution	Native	854 x 480
Resolution	Support	VGA (640 x 480) to Full HD (1920 x 1080)
Input	HDMI	1 (HDMI 1.4, HDCP 1.4)
	SD Card	1 (Micro SD; support up to 32 GB, SDHC)
	USB Type-C	1 (5V/2A)
	Wi-Fi	1
	Bluetooth	1
Output	Speaker	3W Cube x 2
	USB Type-A (Power)	1 (USB 2.0, 5V/1A; share with USB reader)
	Audio Out (3.5 mm)	1
Power Adapter	Input Voltage	AC 100-240V, 50/60 Hz (auto switch)
Operating Conditions	Temperature	0°C to 40°C (32°F to 104°F)
Operating Conditions	Humidity	0% to 90% (non-condensing)
Dimensions	Physical (W x H x D)	146 x 126 x 40 mm (5.7” x 4.9” x 1.57”)
Weight	Physical	0.75 kg (1.6 lbs)
Power Consumption	On	45W (Typical)
Power Consumption	Off	< 0.5W (Standby)

Timing Charts

HDMI Video Timing

Timing	Resolution	Horizontal Frequency (KHz)	Vertical Frequency (Hz)	Dot Clock Frequency (MHz)
480i	720(1440) x 480	15.73	59.94	27
480p	720 x 480	31.47	59.94	27
576i	720(1440) x 576	15.63	50	27
576p	720 x 576	31.25	50	27
720/50p	1280 x 720	37.5	50	74.25
720/60p	1280 x 720	45	60	74.25
1080/50i	1920 x 1080	28.13	50	74.25
1080/60i	1920 x 1080	33.75	60	74.25
1080/24p	1920 x 1080	27	24	74.25
1080/25p	1920 x 1080	28.13	25	74.25
1080/30p	1920 x 1080	33.75	30	74.25
1080/50p	1920 x 1080	56.25	50	148.5
1080/60p	1920 x 1080	67.5	60	148.5

HDMI Support PC Timing

Resolution	Refresh Rate (Hz)	Horizontal Frequency (kHz)	Dot Clock Frequency (MHz)
640 x 480	59.94	31.469	25.175
	72.809	37.861	31.5
	75	37.5	31.5
	85.008	43.269	36
720 x 400	70.087	31.469	28.3221
800 x 600	56.250	35.156	36
	60.317	37.879	40
	72.188	48.077	50
	75	46.875	49.5
	85.061	53.674	56.250
	119.854	77.425	83
1024 x 768	60.004	48.363	65
	70.069	56.476	75
	75.029	60.023	78.75
	84.997	94.500	94.500
	119.804	137.750	137.750
1152 x 864	75	67.5	108
1280 x 768	59.87	47.776	79.5
	60	47.369	68.25
	74.893	60.289	102.25
	84.837	68.633	117.50
1280 x 800	59.81	49.702	83.5
	74.934	62.795	106.5
	84.880	71.554	122.500
1280 x 960	60	60	108
1280 x 960	85.002	85.938	148.500
1280 x 1024	60.02	63.981	108
	75.025	79.976	135
	85.024	91.146	157.500
1360 x 768	60.015	47.712	85.5
1400 x 1050	59.978	65.317	121.75
1440 x 900	59.887	55.935	106.5
	60	55.469	88.75
	74.984	70.635	136.75
	84.842	80.430	157
1600 x 1200	60	75	162
1680 x 1050	59.883	64.674	119
1680 x 1050	59.954	65.29	146.25
1920 x 1200	59.950	74.038	154
640 x 480 @ 67Hz	66.667	35	30.240
832 x 624 @ 75Hz	74.546	49.722	57.280
1024 x 768 @ 75Hz	75.020	60.241	80
1152 x 870 @ 75Hz	75.06	68.68	100

3D Support Timing

HDMI 3D (BlueRay 3D with info frame)
Signal	Resolution (dots)	Aspect Ratio	Refresh Rate (Hz)	Support
Frame Packing
1080p	1920 x 1080	16:9	23.98/24	Yes
720 p	1280 x 720	16:9	50/59.94/60	Yes
Side by Side
1080i	1920 x 1080	16:9	50/59.94/60	Yes
Top and Bottom
1080p	1920 x 1080	16:9	23.98/24	Yes
720 p	1280 x 720	16:9	50/59.94/60	Yes

3D (HDMI/USB-C) Manual Setting
Signal	Resolution (dots)	Aspect Ratio	Refresh Rate (Hz)	Support
SVGA	800 x 600	4:3	60/120*	Yes
XGA	1024 x 768	4:3	60/120*	Yes
HD	1280 x 720	16:9	60/120*	Yes
WXGA	1280 x 800	16:9	60/120*	Yes
HDTV(1080p)	1920 x 1080	16:9	60	Yes
Video Signal
SDTV(480i)***	720 x 480	4:3/16:9	60	No

NOTE:

[ * ] 60Hz signals are supported for side by side, top and bottom, and frame sequential.
[ ** ] 120Hz signals are supported for frame sequential only.
[ *** ] Video signal (SDTV 480i) is supported for frame sequential only.

USB-C Support Timing

Timing	Resolution	Horizontal Frequency (KHz)	Vertical Frequency (Hz)	Dot Clock Frequency (MHz)
480i	720(1440) x 480	15.73	59.94	27
480p	720 x 480	31.47	59.94	27
576i	720(1440) x 576	15.63	50	27
576p	720 x 576	31.25	50	27
720/50p	1280 x 720	37.5	50	74.25
720/60p	1280 x 720	45	60	74.25
1080/50i	1920 x 1080	28.13	50	74.25
1080/60i	1920 x 1080	33.75	60	74.25
1080/24p	1920 x 1080	27	24	74.25
1080/25p	1920 x 1080	28.13	25	74.25
1080/30p	1920 x 1080	33.75	30	74.25
1080/50p	1920 x 1080	56.25	50	148.5
1080/60p	1920 x 1080	67.5	60	148.5

Compliance Information

This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

FCC Compliant Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

The following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance	Proposed Maximum Concentration	Actual Concentration
Lead (Pb)	0.1%	< 0.1%
Mercury (Hg)	0.1%	< 0.1%
Cadmium (Cd)	0.01%	< 0.01%
Hexavalent Chromium (Cr6⁺)	0.1%	< 0.1%
Polybrominated biphenyls (PBB)	0.1%	< 0.1%
Polybrominated diphenyl ethers (PBDE)	0.1%	< 0.1%
Bis (2-Ethylhexyl) phthalate (DEHP)	0.1%	< 0.1%
Benzyl butyl phthalate (BBP)	0.1%	< 0.1%
Dibutyl phthalate (DBP)	0.1%	< 0.1%
Diisobutyl phthalate (DIBP)	0.1%	< 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below. Examples of exempted components are:

Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

Short length (500 mm): maximum 3.5 mg per lamp.
Medium length (>500 mm and 1,500m): maximum 5 mg per lamp.
Long length (> 1,500 mm): maximum 13 mg per lamp.

Lead in glass of cathode ray tubes.
Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
Lead as an alloying element in aluminum containing up to 0.4% lead by weight.
Copper alloy containing up to 4% lead by weight.
Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Product Disposal at End of Product Life

ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

USA & Canada
https://www.viewsonic.com/us/company/green/go-green-with-viewsonic/#recycle-program

Europe
http://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan
https://recycle.epa.gov.tw/

Copyright Information

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.

ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).

As an ENERGY STAR® partner, ViewSonic® Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.

Customer Service Contact Information

For technical support or product service, see the table below or contact your reseller.

Note: You will need the product’s serial number, which is located on the rear of the monitor by the I/O ports.

Asia Pacific & Africa

Country / Region	Website
Australia	https://viewsonic.com/au/
Bangladesh	https://www.viewsonic.com/bd/
中囯(China)	https://www.viewsonic.com.cn
香港 (繁體中文)	https://www.viewsonic.com/hk/
Hong Kong (English)	https://www.viewsonic.com/hk-en/
India	https://www.viewsonic.com/in/
Indonesia	https://www.viewsonic.com/id/
Israel	https://www.viewsonic.com/il/
日本 (Japan)	https://www.viewsonic.com/jp/
Korea	https://www.viewsonic.com/kr/
Malaysia	https://www.viewsonic.com/my/
Middle East	https://www.viewsonic.com/me/
Myanmar	https://www.viewsonic.com/mm/
Nepal	https://www.viewsonic.com/np/
New Zealand	https://www.viewsonic.com/nz/
Pakistan	https://www.viewsonic.com/pk/
Philippines	https://www.viewsonic.com/ph/
Singapore	https://www.viewsonic.com/sg/
臺灣 (Taiwan)	https://www.viewsonic.com/tw/
ประเทศไทย (Thailand)	https://www.viewsonic.com/th/
Việt Nam	https://www.viewsonic.com/vn/
South Africa & Mauritius	https://www.viewsonic.com/za/

Americas

Country / Region	Website
United States	https://www.viewsonic.com/us/
Canada	https://www.viewsonic.com/us/
Latin America	https://www.viewsonic.com/la/

Europe

Country / Region	Website
Europe	https://www.viewsonic.com/eu/
France	https://www.viewsonic.com/fr/
Deutschland	https://www.viewsonic.com/de/
Қазақстан	https://www.viewsonic.com/kz/
Россия	https://www.viewsonic.com/ru/
España	https://www.viewsonic.com/es/
Türkiye	https://www.viewsonic.com/tr/
Україна	https://www.viewsonic.com/ua/
United Kingdom	https://www.viewsonic.com/uk/

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic® will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty:

Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp from the date of the first consumer purchase.

Other regions or countries: Please check with your local dealer or local ViewSonic® office for the warranty information.

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic® office for the warranty information. Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

What the warranty does not cover:

Any product on which the serial number has been defaced, modified, or removed.
Damage, deterioration, or malfunction resulting from:
- Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
- Operation outside of product specifications.
- Operation of the product for other than the normal intended use or not under normal conditions.
- Repair or attempted repair by anyone not authorized by ViewSonic®.
- Any damage of the product due to shipment.
- Removal or installation of the product.
- Causes external to the product, such as electric power fluctuations or failure.
- Use of supplies or parts not meeting ViewSonic’s specifications.
- Normal wear and tear.
- Any other cause which does not relate to a product defect.
Removal, installation, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic® Customer Support (Please refer to the “Customer Support” page). You will need to provide your product’s serial number.
To obtain warranted service, you will be required to provide: (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
Take or ship the product, freight prepaid, in the original container to an authorized ViewSonic® service center or ViewSonic®.
For additional information or the name of the nearest ViewSonic® service center, contact ViewSonic®.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic® shall not be liable for:

Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
Any other damages, whether incidental, consequential or otherwise.
Any claim against the customer by any other party.

Effect of state law:

This warranty gives you specific legal rights, and you may also have other rights which vary from local authority. Some local governments do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic® products sold outside of the U.S.A. and Canada, contact ViewSonic® or your local ViewSonic® dealer. The warranty period for this product in mainland China (Hong Kong, Macao, and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card. For users in Europe and Russia, full details of warranty provided can be found at: ViewSonic EU under “Support/Warranty Information”.

Mexico Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic® will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.

How long the warranty is effective:

3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.

Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.

All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

What the warranty excludes and does not cover:

Any product on which the serial number has been defaced, modified or removed.
Damage, deterioration, or malfunction resulting from:
- Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
- Any damage of the product due to shipment.
- Causes external to the product, such as electrical power fluctuations or failure.
- Use of supplies or parts not meeting ViewSonic®’s specifications.
- Normal wear and tear.
- Any other cause which does not relate to a product defect.
Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.
Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic® Customer Support (Please refer to the attached “Customer Service” page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.

For information about receiving service under warranty, contact ViewSonic® Customer Support (Please refer to the “Customer Service” page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.
To obtain warranty service, you will be required to provide: (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
Take or ship the product, freight prepaid, in the original container to an authorized ViewSonic® service center.
Round trip transportation costs for in-warranty products will be paid by ViewSonic®.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

Exclusion of damages:

ViewSonic®’s liability is limited to the cost of repair or replacement of the product. ViewSonic® shall not be liable for:

Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
Any other damages, whether incidental, consequential or otherwise.
Any claim against the customer by any other party.
Repair or attempted repair by anyone not authorized by ViewSonic®.

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.P: 83140 Tel: 01-66-22-14-9005 E-Mail: disc2@hmo.megared.net.mx	Villahermosa: Compumantenimietnos Garantizados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz): RENTA Y DATOS, S.A. DE C.V. Domicilio: 29 SUR 721 COL. LA PAZ 72160 PUEBLA, PUE. Tel: 01(52).222.891.55.77 CON 10 LINEAS E-Mail: datos@puebla.megared.net.mx	Veracruz, Ver.: CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419 ENTRE PINZÓN Y ALVARADO Fracc. Reforma C.P. 91919 Tel: 01-22-91-00-31-67 E-Mail: gacosta@qplus.com.mx
Chihuahua: Soluciones Globales en Computación C. Magisterio # 3321 Col. Magisterial Chihuahua, Chih. Tel: 4136954 E-Mail: Cefeo@soluglobales.com	Cuernavaca: Compusupport de Cuernavaca SA de CV Francisco Leyva # 178 Col. Miguel Hidalgo C.P. 62040, Cuernavaca Morelos Tel: 01 777 3180579 / 01 777 3124014 E-Mail: aquevedo@compusupportcva.com
Distrito Federal: QPLUS, S.A. de C.V. Av. Coyoacán 931 Col. Del Valle 03100, México, D.F. Tel: 01(52)55-50-00-27-35 E-Mail : gacosta@qplus.com.mx	Guadalajara, Jal.: SERVICRECE, S.A. de C.V. Av. Niños Héroes # 2281 Col. Arcos Sur, Sector Juárez 44170, Guadalajara, Jalisco Tel: 01(52)33-36-15-15-43 E-Mail: mmiranda@servicrece.com
Guerrero Acapulco: GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero Tel: 744-48-32627	Monterrey: Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: aydeem@gps1.com.mx
MERIDA: ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: rrrb@sureste.com	Oaxaca, Oax.: CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col. Centro, 68000, Oaxaca Tel: 01(52)95-15-15-22-22 Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com
Tijuana: STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembr Tijuana, Mexico	FOR USA SUPPORT: ViewSonic® Corporation 381 Brea Canyon Road, Walnut, CA. 91789 USA Tel: 800-688-6688 http://www.viewsonic.com

Using the Projector Safely

Please read the following Safety Precautions before you start using the projector.

Keep this user guide in a safe place for later reference.
Read all warnings and follow all instructions.
Allow at least 20“ (50 cm) clearance around the projector to ensure proper ventilation.
Place the projector in a well-ventilated area. Do not place anything on the projector that prevents heat dissipation.
Do not place the projector on an uneven or unstable surface. The projector may fall over, causing personal injury or projector malfunction.
Do not use if the projector is tilted at an angle of more than 10° degrees left or right, nor at an angle of more than 15° degrees forwards or backwards.
Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.
Always open the lens shutter or remove the lens cap when the projector lamp is on.
Do not block the projection lens with any objects when the projector is under operation as this could cause objects to become heated and deformed or even cause a fire.
The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the rated life could cause them to break on rare occasions.
Never replace the lamp assembly or any electronic component unless the projector is unplugged.
Do not attempt to disassemble the projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts.
When moving the projector, be careful not to drop or bump the projector on anything.
Do not place any heavy objects on the projector or connection cables.
Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing personal injury or projector malfunction.
Avoid exposing the projector to direct sunlight or other sources of sustained heat. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that may increase the temperature of the projector to dangerous levels.

Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply and call your local service center to have the projector serviced.
When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal operation and not a defect.
Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide and third blade are provided for your safety. If the plug does not fit into your outlet, obtain an adapter and do not attempt to force the plug into the outlet.
When connecting to a power outlet, DO NOT remove the grounding prong. Please ensure grounding prongs are NEVER REMOVED.
Protect the power cord from being treaded upon or pinched, particularly at the plug, and at the point where it emerges from the projector.
In some countries, the voltage is NOT stable. This projector is designed to operate safely within a voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector, or uninterruptable power supply (UPS).
If smoke, an abnormal noise, or a strange odor is present, immediately switch the projector off and call your dealer or ViewSonic®. It is dangerous to continue using the projector.
Use only attachments/accessories specified by the manufacturer.
Disconnect the power cord from the AC outlet if the projector is not being used for a long period of time.
Refer all servicing to qualified service personnel.

CAUTION: Possibly hazardous optical radiation is emitted from this product. As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015

Glossary of Terms

Note: Some terms may not be applicable to your device.

Aspect Ratio

Refers to the ratio of the image width to the image height.

Brightest Mode

Maximizes the brightness of the projected image. This mode is ideal for environments where extra-high brightness is required, such as using the projector in well lit rooms.

Brightness

Adjusts background black levels of the screen image.

CEC (Consumer Electronics Control)

Synchronizes power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.

Color

Adjusts the color saturation.

Color Temperature

Allows users to select specific color temperature settings to further customize their viewing experience.

Contrast

Adjusts the difference between the image background (black level) and the foreground (white level).

Focus

Manually improve the clarity of the projected image.

Gamma

Allows the user to manually select the greyscale curve of the projector.

HDMI

Audio/Video interface used to transmit video and audio via a single cable.

HDMI Range

Allows the user to select HDMI greyscale range between 0~255 (full range) , 16~240 (limited range) or Auto by the signal type detected.

HDR (High-Dynamic Range)

Keeps the brightness level and enhances details on the dark level.

High Altitude Mode

Optional mode for users who live in an environment between 1,500 m and 3,000 m above sea level, and the temperature is between 5° C and 25° C. Activating it will improve projector cooling and performance.

Information

Displays the timing mode (video signal input), the projector model number, the serial number, and the ViewSonic® website URL.

Input Select

Toggles between the various input options that are available for the projector.

Keystone

The distortion of an image caused by projecting it onto an angled surface.

Light Source Level

Use Normal or Eco mode to adjust the brightness level and power consumption.

Movie Mode

A Picture Mode appropriate for playing colorful movies, video clips from digital cameras, or DVs through the PC input. Best for a low light environment.

Sharpness

Adjusts the picture quality.

Troubleshooting Common Problems

Why doesn't the projector turn on?

Solution 1 ► Ensure the power cord is properly attached to the projector and to the power outlet.

Solution 2 ► If the cooling process has not completed, please wait until it has finished then try to turn on the projector again.

Solution 3 ► If the above does not work, try another power outlet or another electrical device with the same power outlet.

Solution 4 ► Check that the battery has remaining power, or needs external power.

Why is there no picture?

Solution 1 ► Ensure the video source cable is connected properly, and that the video source is turned on.

Solution 2 ► If the input source is not selected automatically, select the correct source with the Source key on either the projector or the remote control.

What should I do if the image is blurry?

Solution 1 ► Adjusting the Focus Ring will help correctly focus the projection lens.

Solution 2 ► Ensure the projector and screen are aligned properly. If necessary, adjust the height of the projector as well as the projection angle and direction.

Why is the remote control not working?

Solution 1 ► Ensure there are no obstacles between the remote control and projector; and that they are within 8 m (26 ft) of each other.

Solution 2 ► The batteries may be out of power, please check and replace if necessary.

What should I do if the projector freezes or doesn't respond?

Solution ► Using a paper clip, carefully insert it into the Reset button at the rear of the projector to reset the device.

Maintaining the Projector

General Precautions

Make sure the projector is turned off and the power cable is unplugged from the power outlet.
Never remove any parts from the projector. Contact ViewSonic® or a reseller when any part of the projector needs replacing.
Never spray or pour any liquid directly onto the case.
Handle the projector with care, as a darker-colored projector, if scuffed, may show marks more clearly than a lighter-colored projector.

Cleaning the Lens

Use a canister of compressed air to remove dust.
If the lens is still not clean, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the surface.

Important: Never rub the lens with abrasive materials.

Cleaning the Case

Use a soft, lint-free, dry cloth to remove dirt or dust.
If the case is still not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.

Important: Never use wax, alcohol, benzene, thinner, or other chemical detergents.

Storing the Projector

If you intend to store the projector for an extended period of time:

Ensure the temperature and humidity of the storage area are within the recommend range.
Retract the adjuster foot completely.
Remove the batteries from the remote control.
Pack the projector in its original packaging or equivalent.

Disclaimer

ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the lens or case. Some chemical cleaners have been reported to damage the lens and/or case of the projector.
ViewSonic® will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.

[1] In the event of a system crash, use the Reset Button to restart the projector.

[2] Blank the projection image and focus on the music.

[id-3] 1.0 ^1.1 A rear projection screen is required.

[1]

[1]

[1]