AirPen (VB-PEN-007)
Package Contents
Please take a moment to check if all the necessary items are included in the package. If anything is missing or damaged, please contact your dealer immediately.
Product Overview
Charging the AirPen
- Connect the USB Type C end of the included USB cable to the Charging Port of the AirPen (VB-PEN-007).
- Then connect the other end, the USB Type A, of the cable to a USB Type A port of a display or other power delivering device.
- When charging, the LED Indicator will be a steady red. When fully charged, the VB-PEN-007 can provide four (4) hours of use.
Powering On and Pairing the AirPen
- Plug the USB Receiver into a USB Type A port of a display device.
- Press and hold the AirPen's (VB-PEN-007) Power Button for three (3) seconds to begin pairing.
- After successfully powering on and pairing the VB-PEN-007, the LED Indicator will be a steady blue.
Re-Pairing the AirPen
If the AirPen (VB-PEN-007) needs to be re-paired, please follow the steps below:
- Remove the USB Receiver from the display device.
- Press and hold both the Volume Up and Volume Down buttons on the AirPen (VB-PEN-007) for three (3) seconds to enter pairing mode.
- Plug the USB Receiver into a USB Type A port of the display device.
- When paired successfully, the LED Indicator will be a steady blue.
Pen Nibs
The AirPen (VB-PEN-007) is equpped with two (2) pen nibs.
| Fine Nib | Thick Nib | |
|---|---|---|
 |
 | |
| Pen nib for infrared (IR) screens. | Conductive pen nib for infrared (IR) and capacitive screens. |
Replacing Pen Nibs
When the pen nib develops a sharp or rough edge, it can be replaced with replacement nibs. To replace a nib:
- Rotate the pen nib holder counterclockwise and remove the old pen nib.
- Insert the new pen nib and turn the pen nib holder clockwise to secure it.
Using the Presenter Function
You can press and hold the Air Mouse button to use the AirPen (VB-PEN-007) as an onscreen cursor, use the Previous Page and Next Page buttons as a previous page and next page switch, and the side Volume Up and Down buttons to control the volume level.
Pressing the Air Mouse button and Power Button at the same time will function as a left mouse click button.
Technical Specifications
| Item | Specifications |
|---|---|
| Model No. | VS19566 |
| P/N | VB-PEN-007 |
| Wireless Connection Type | RF 2.4 GHz, 802.11b |
| Wireless Connection Distance | 30 m (98.43 ft) |
| Indicator Type | Air Mouse |
| Battery Type | Li-ion Polymer Battery, ALP500950, 170mAh |
| Battery Life | 50 days (Rechargeable) |
| Input Power Rating | 5V/210mA, 1.05W |
| Antenna Type | Chip Antenna |
| Automatic Sleep Mode | 20 minutes of inactivity |
| Operating Temperature | 40° C (104° F) |
| Operating System Compatibility | Windows/Android/MacOS/Linux |
| Dimensions | 153.5 x 18.7 x 18.3 mm (6.04 x 0.74 x 0.72 in) |
| Weight | 21g (0.46 lbs) |
USB Receiver Specifications
| Item | Specifications |
|---|---|
| Model No. | VS19567 |
| P/N | VB-PEN-007-2 |
| Wireless Connection Type | RF 2.4 GHz, 802.11b |
| Wireless Connection Distance | 30 m (98.43 ft) |
| Supported USB | USB 1.1 compatible with USB 2.0 and 3.0 |
| Input Power Rating | 5V/16mA, 0.08W |
| Antenna Type | PIFA |
| Dimensions | 21.1 x 12.1 x 4.7 mm (0.83 x 0.48 x 0.19 in) |
| Weight | 1.5 g (0.003 lbs) |
LED Indicator Status
| Indicator Light | Specifications |
|---|---|
| Blue (Steady) | Powered on and paired |
| Blue (Flashing Quickly) | Pairing in progress |
| Blue (Flashing Slowly) | Low battery |
| Red (Steady) | Charging |
Compliance Information
This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Industry Canada Statement
CAN ICES-003(B) / NMB-003(B)
| AirPen | VS19566 (VB-PEN-007) |
USB Receiver | VS19567 (VB-PEN-007-2) | |
| FCC ID: | GSS-VS19566 | FCC ID: | GSS-VS19567 | |
| IC ID: | 4280A-VS19566 | IC ID: | 4280A-VS19567 |
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body.
Validity of using the module certification
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Custom design antennas may be used, however the OEM installer must following the FCC 15.21 requirements and verify if new FCC approval will be necessary.
IC Warning Statement
This device complies with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : ( 1 ) l’appareil ne doit pas produire de brouillage, et ( 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement.
CE Conformity for European Countries
 |
The device complies with the EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and Radio Equipment Directive 2014/53/EU. https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS19566_CE_DoC.pdf https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS19567_CE_DoC.pdf |
The following information is only for EU-member states:
| The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law. |  |
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below.
| Substance | Proposed Maximum Concentration | Actual Concentration |
|---|---|---|
| Lead (Pb) | 0.1% | < 0.1% |
| Mercury (Hg) | 0.1% | < 0.1% |
| Cadmium (Cd) | 0.01% | < 0.01% |
| Hexavalent Chromium (Cr6⁺) | 0.1% | < 0.1% |
| Polybrominated biphenyls (PBB) | 0.1% | < 0.1% |
| Polybrominated diphenyl ethers (PBDE) | 0.1% | < 0.1% |
| Bis (2-ethylhexyl) phthalate (DEHP) | 0.1% | < 0.1% |
| Butyl benzyl phthalate (BBP) | 0.1% | < 0.1% |
| Dibutyl phthalate (DBP) | 0.1% | < 0.1% |
| Diisobutyl phthalate (DIBP) | 0.1% | < 0.1% |
Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below. Examples of exempted components are:
- Copper alloy containing up to 4% lead by weight.
- Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
- Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
- Lead in dielectric ceramic in capacitors for a rated voltage of 125 V AC or 250 V DC or higher.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.
USA & Canada:
https://www.viewsonic.com/us/go-green-with-viewsonic
Europe:
https://www.viewsonic.com/eu/environmental-social-governance/recycle
Taiwan:
https://recycle.moenv.gov.tw/
For EU users, please contact us for any safety/accident issue experienced with this product:
 |
ViewSonic Europe Limited Haaksbergweg 75 1101 BR Amsterdam Netherlands |
 |
+31 (0) 650608655 |
 |
EPREL@viewsoniceurope.com |
 |
https://www.viewsonic.com/eu/ |
Copyright Information
Copyright© ViewSonic® Corporation, 2023. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.
ViewSonic® and the three birds logo are registered trademarks of ViewSonic® Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR® partner, ViewSonic® Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.
VB-PEN-007_UG_ENG_1a_20231012
For technical support or product service, see the table below or contact your reseller.
Americas
| Country/Region | Website |
|---|---|
| Canada | https://www.viewsonic.com/us |
| Latin America | https://www.viewsonic.com/la |
| United States | https://www.viewsonic.com/us |
Asia Pacific & Africa
| Country/Region | Website |
|---|---|
| Australia | https://viewsonic.com/au/ |
| Bangladesh | https://www.viewsonic.com/bd/ |
| 中国 (China) | https://www.viewsonic.com.cn |
| 香港 (繁體中文) | https://www.viewsonic.com/hk/ |
| Hong Kong (English) | https://www.viewsonic.com/hk-en/ |
| India | https://www.viewsonic.com/in/ |
| Indonesia | https://www.viewsonic.com/id/ |
| Israel | https://www.viewsonic.com/il/ |
| 日本 (Japan) | https://www.viewsonic.com/jp/ |
| Korea | https://www.viewsonic.com/kr/ |
| Malaysia | https://www.viewsonic.com/my/ |
| Middle East | https://www.viewsonic.com/me/ |
| Myanmar | https://www.viewsonic.com/mm/ |
| Nepal | https://www.viewsonic.com/np/ |
| New Zealand | https://www.viewsonic.com/nz/ |
| Pakistan | https://www.viewsonic.com/pk/ |
| Philippines | https://www.viewsonic.com/ph/ |
| Singapore | https://www.viewsonic.com/sg/ |
| 臺灣 (Taiwan) | https://www.viewsonic.com/tw/ |
| ประเทศไทย | https://www.viewsonic.com/th/ |
| Việt Nam | https://www.viewsonic.com/vn/ |
| South Africa & Mauritius | https://www.viewsonic.com/za/ |
Europe
| Country/Region | Website |
|---|---|
| Europe | https://www.viewsonic.com/eu/ |
| France | https://www.viewsonic.com/fr/ |
| Deutschland | https://www.viewsonic.com/de/ |
| Қазақстан | https://www.viewsonic.com/kz/ |
| Россия | https://www.viewsonic.com/ru/ |
| España | https://www.viewsonic.com/es/ |
| Türkiye | https://www.viewsonic.com/tr/ |
| Україна | https://www.viewsonic.com/ua/ |
| United Kingdom | https://www.viewsonic.com/uk/ |