VPCF5-2A

Introduction

Product Overview

Number	Item	Description
1	Antenna	Wi-Fi antenna interface.
2	Security Lock	Anti-theft security lock.
3	USB 3.1	USB 3.1 port.
4	LAN	Standard RJ45 (10M/100M/1G) internet connection port.
5	USB 2.0	USB 2.0 port.
6	RESET	Reset button.
7	Power Button	Turn the slot-in PC on or off.
8	Status LED	Status indicator light (Green).
		Off Indicator light is off.
		On Green indicator light is flashing.
9	Power LED	Power indicator light (Red).
		Off Indicator light is off.
		On Green indicator light is always on.
10	LINE-OUT	Audio out for connected headphones or speakers.
11	DP	Extend content out to another display device.
12	HDMI	Extend content out to another display device.
13	USB Type C	USB Type C input (Data only; 5V/0.9A charging)

Initial Setup

1. Remove the slot-in PC cover of the display.
2. Using the handle of the VPCF5-2A, carefully insert it into the PC slot of the display.
3. Secure the VPCF5-2A to the display with the two included screws.

Note:

• Please note that the antennas must be installed on the VPCF5-2A.
• Please pay attention to the installation direction of the VPCF5-2A, with the vents facing outwards to avoid damage.
• The VPC products do not support hot swapping. When removing or installing the device, turn off the power supply for both the display and VPC product first.

Network Connection

To connect to the Internet or a network, connect one end of a RJ45 cable to the LAN port of the VPCF5-2A, then connect the other end to your network.

USB Connection

USB peripherals such as keyboards, mice, storage devices, etc. can be connected to the VPCF5-2A’s USB ports.

Using the Device

Selecting an Input Source

IFP Series

To select an input source:

1. Press INPUT/ on the remote control, press the setting button on the front panel, or press the Settings icon from the toolbar to display the Input Settings menu.
2. Press ▼/▲/◄/► on the remote control to select the PC source.
3. Press OK/ENTER on the remote control, or touch the input source directly.
4. Press EPG/BACK/ on the remote control, or touch a blank area outside of the menu to exit.
   Note: The above image is for reference only and is subject to change without notice.

CDE Series

To select an input source:

1. Press INPUT/ on the remote control.
2. Press ▼/▲ on the remote control to select the PC source.
3. Press OK/ENTER on the remote control.
4. Press EPG/BACK/ on the remote control to exit.
   Note: The above image is for reference only and is subject to change without notice.

Appendix

Specifications

Category	Item	Specifications
I/O	Ports	1 x HDMI (Max: 3840 x 2160 @ 60 Hz) 1 x HDMI (Max: 7680 x 4320 @ 30 Hz) 1 x RJ45 (LAN) (10M/100M/1G) 2 x USB 2.0 (5V/0.5A) 2 x USB 3.1 (5V/0.9A) 1 x USB Type (Data only, no PD support, 5V/900mA) 1 x Analog audio-in(3.5 mm, mic-in)
Physical	Dimensions	180 x 120 x 30 mm
		7.09" x 4.72" x 1.18"
	Weight	0.75 kg
		1.65 lb
Operating Conditions	Altitude	< 5000 m
		< 16,404.2 ft
	Relative Humidity	10% ~ 90% (non-condensing)
	Temperature	-5°C ~ 45°C
		23°F ~ 113°F
Storage Conditions	Altitude	< 5000 m
		< 16,404.2 ft
	Relative Humidity	10% ~ 90% (non-condensing)
	Temperature	-20°C ~ 70°C
		-4°F ~ 158°F
Power	Voltage	12~19V DC
	Consumption	90W (Maximum)
Wi-Fi Module	Form Factor	Wi-Fi 6 (IEEE 802.11 a/b/g/n/ac/ax Wi-Fi 2T/2R+)
		Bluetooth 5.2 (V2.1/4.2/5.2 USB2.0/3.0 Module)
	Frequency Range and Output Power (Max.)	BT 2.4 Ghz~2.4835 Ghz (< 10dBm) Wi-Fi 2.4 GHz~2.4835 GHz (< 20dBm) 5.170 GHz~5.33 GHz (< 20dBm) 5.49 GHz~5.73 GHz (< 20dBm) 5.735 GHz~5.835 GHz (< 20dBm)