View source for XG251G Initial Setup

<noinclude>
{{Sticky_Menu_Monitor_3.0_SUF
|1=XG251G_Introduction
|2=XG251G_Initial_Setup
|3=XG251G_Connecting_Power_and_Devices
|4=XG251G_Adjusting_the_Viewing_Angle
|5=XG251G_Quick_Menu
|6=XG251G_Hot_Keys
|7=XG251G_On-Screen_Display_Menu
|8=XG251G_On-Screen_Display_Menu_Tree
|9=XG251G_On-Screen_Display_Menu_Options
|10=XG251G_Advanced_Features_and_Settings
|11=XG251G_Specifications
|12=XG251G_Regulatory_and_Service_Information
}}
</noinclude>  __NOTOC__
=Stand Installation=
# Place the monitor on a flat, stable surface with the screen facing down.
# Align and connect the two (2) points on the monitor stand’s base with the monitor stand’s neck.
# Use the captured screw in the monitor stand’s base and secure it to the monitor stand’s neck.
# Align and slide the upper hooks of the monitor stand into the stand mounting slots as shown in the illustration.
# Using the stand’s handle, lift the device into its upright position on a flat, stable surface.

<gallery widths=200px heights=200px mode="nolines">
XG270QG_Install_1.png| Align the base with the neck
XG270QG_Install_2.png| Align the hooks 
XG270QG_Install_3.png| Lift into an upright position
</gallery>
{{Note-yellow|Always place the device on a flat, stable surface. Failure to do so may cause the device to fall and damage the device and/or result in personal injury.}}

=Using the Mouse Anchor=
Included at the rear of the display, under the I/O ports, are two mouse anchors. Use these to prevent mouse cable dragging and personalize your mouse use setup.

<gallery widths=300px heights=300px mode="nolines">
XG320Q_Mouse_1.png
XG320Q_Mouse_2.png
</gallery>

=Wall Mounting=
Refer to the table below for the standard dimensions for wall mount kits.

{{Note-yellow|For use only with a UL certified wall mount kit/bracket. To obtain a wall-mounting kit or height adjustment base, contact ViewSonic® or your local dealer.}}

{| class="wikitable" style="text-align: center;" 
! style="background-color:#c41230; color:#ffffff;" | Maximum Loading
! style="background-color:#c41230; color:#ffffff;" | Hole Pattern (W x H)
! style="background-color:#c41230; color:#ffffff;" | Interface Pad (W x H x D)
! style="background-color:#c41230; color:#ffffff;" | Pad Hole
! style="background-color:#c41230; color:#ffffff;" | Screw Specification & Quantity
|-
|14 kg
|100 x 100 mm
|115 x 115 x 2.6 mm
|Ø 5 mm
|M4 x 10 mm - 4 pieces
|}

# Turn off the device and disconnect all cables.
# Place the device on a flat, stable surface with the screen facing down.
# Press and hold the quick release tab and carefully lift the stand.
# Pull down slightly to disengage the hooks and remove the stand.
# Attach the mounting bracket to the VESA mounting holes at the rear of the monitor. Then secure it with four (4) screws (M4 x 10 mm).
# Follow the instructions that come with the wall mounting kit to mount the monitor onto the wall.

<gallery widths=200px heights=200px mode="nolines">
XG270QG_Wall_Mount_1.png| Disengage the hooks
XG270QG_Wall_Mount_2.png| VESA mounting points
</gallery>

<noinclude>=[[Monitor_Security_Slot| Using the Security Slot]]=</noinclude>

{{#seo:
|title=ViewSonic Monitor
|title_mode=append
|keywords=XG251G, stand installation, wall mounting, VESA 
|description=How to install and uninstall the stand on the XG251UG monitor. 
}}

[[Category:XG251G]]