View source for LD108-121 Wall Installation

<noinclude>
{{Sticky_Menu_DirectView
|1=LD108-121_Introduction
|2=LD108-121_Remote_Control
|3=LD108-121_Wall_Installation
|4=LD108-121_Floor_Stand_Installation
|5=LD108-121_Connecting_Devices
|6=LD108-121_Using_the_Display
|7=LD108-121_On-Screen_Display_Menu
|8=LD108-121_Embedded_Applications
|9=LD108-121_RS-232_Protocol
|10=LD108-121_Specifications
|11=LD108-121_Regulatory_and_Service_Information
}} 
{{Top}} </noinclude>
=Before Installation=
<ol style="list-style-type:square"><li>Maintain an adequate air gap between the back of the display and any wall for proper ventilation.</li>
<li>Ensure there is no direct airflow from air conditioning or heating vents blowing on the display.</li>
<li>Avoid installing the display in places with high humidity.</li>
<li>Due to high power usage, always use power cords specifically designed for this product.</li></ol>

=Wall Mounting=

==Installing the Upper and Lower Mounting Brackets==

<ol>
<div class="res-img">[[File:LD_LDM_108_Wall_Mounting_Bracket.svg|600px]]</div>
<li>Ensure the wall area and size is an appropriate installation site.</li>
:'''NOTE:''' The height of the Upper Wall Mount Brackets must not be less than 78-3/4" (2 meters) from the ground.

<li>Using the ''Wall Mount Bracket'' (pictured above) as a guide, mark each of the holes and pre-drill each.</li>

<li>Install the first Upper ''Wall Mount Bracket'' with the provided screws (M6x50mm Expansion for masonry; TA6x30mm for load bearing wood).</li>

<li>Repeat '''Step 2''', ensuring the second Upper ''Wall Mount Bracket'' is level with the first upper bracket.</li>
:<div class="res-img">[[File:LD_Wall_Mounting_After_Upper_Brackets.svg|400px]]</div>

<li>Install the Lower ''Wall Mount Brackets'' in the same manner as the Upper ''Wall Mount Brackets''. The distance between the Upper and Lower ''Wall Mount Brackets'' is 50.78" (1290 mm).</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_Spacing.png|250px]]</div>

{{Note-yellow|Ensure the wall can safely support 194 lbs. (88 kg).}}
:'''NOTE:''' You can also install the Upper ''Wall Mount Brackets'', hang the screen, and then install the Lower ''Wall Mount Brackets'' for a more precise fit.

<li>After installing both Upper and Lower ''Wall Mount Brackets'', the installation wall should look like:</li>
:<div class="res-img">[[File:LD_Brackets.svg|400px]]</div>
</ol>

==Installing the Middle Cabinets==
<ol>
<li>Ensure the ''Mounting Brackets'' on the rear of the two (2) ''Middle Cabinets'' are positioned at the top and bottom mounting positions as shown below:</li>
:<div class="res-img">[[File:LD108-121_Rear_Middle_Panels_Separate_Original.png|250px]]</div>

<li>Carefully lift each ''Middle Cabinet'' up onto the Upper ''Wall Mount Brackets''.</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_After_Middle_Screens_Update.png|400px]]</div>

<li>Ensure the ''Mounting Brackets'' sit securely on the ''Wall Mount Brackets'' as shown below.</li>
:<div class="res-img">[[File:LD_Wall_Mount_Close_Up.svg|400px]]</div>

<li>Push each ''Locking Bolt'' and lock each ''Hook'' with the hex tool to securely connect each cabinet together.</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_Connecting_Middle_Screens.png|500px]]</div>

:'''NOTE:''' There are four (4) Locking Bolts and eight (8) Hooks between each cabinet.

</ol>

==Installing the Left and Right Cabinet==
<ol>
<li>Ensure the ''Mounting Brackets'' on the rear of the ''Left'' and ''Right Cabinet'' are positioned at the top and bottom mounting positions as shown below:</li>
:<div class="res-img">[[File:LD_Rear_Left_and_Right.svg|250px]]</div>

<li>Carefully lift the ''Left'' and ''Right Cabinet'' up onto the Upper ''Wall Mount Brackets'', ensuring the ''Mounting Brackets'' sit securely on the ''Wall Mount Brackets''.</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_After_All_Screens.png|400px]]</div>

<li>If necessary, adjust the ''Left'' or ''Right Cabinet'' so that they fit seamlessly with the ''Middle Cabinets''.</li>

<li>Push each ''Locking Bolt'' and lock each ''Hook'' with the hex tool to securely connect the ''Left'' and ''Right Cabinets''.</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_Locking_Bolts.png|400px]]</div>

:'''NOTE:''' There are four (4) ''Locking Bolts'' and eight (8) Hooks between each cabinet.
</ol>

==Connecting the System Control Box==
<ol>
<li>Carefully unfold the ''System Control Box'' panel. Ensure the main system control board is on the left.</li>
:'''NOTE:''' Use caution as the ''System Control Box'' panel will be separated into two pieces, however the wires are connected.

<li>Align the holes of the ''Cabinet'' with the ''System Control Box'' to attach.</li>
:<div class="res-img">[[File:LD108-121_Wall_Mounting_Connecting_Box.png|400px]]</div>

<li>Further secure the ''System Control Box'' to the ''Cabinets'' with the 16 provided screws (M6x16mm).</li>
:<div class="res-img">[[File:LD_Box_Install.png|300px]]</div>

<li>Connect the Network and Power cables of the ''Cabinets'' to the ''System Control Box''.</li>

:'''NOTE:''' There are four (4) Network and four (4) Power cables to connect.

:<div class="res-img">[[File:LD108-121_Wall_Mounting_Connecting_Net_Pow.png|400px]]</div>
</ol>

==Installing the LED Modules==
Install each ''LED Module'' onto the ''Cabinets'', being sure to match the corresponding numbers on the ''Module'' to the ''Cabinet''.
{{Note-yellow|Please wear Anti-Static Gloves before installing the LED modules.}}

<div class="res-img">[[File:LD108-121_Wall_Mounting_Modules_1.png|450px]]</div>

Ensure each ''Module'' is flush and that there is little to no gap between each.

:<div class="res-img">[[File:LD163-181_Wall_Mounting_Modules_No_Cover.png|415px]]</div>

==Installing the System Control Box Covers==
There are three (3) System Control Box Covers: Left, Middle, and Right.
<div class="res-img">[[File:LD_Control_Box_Covers.svg|600px]]</div>
<ol><li>Begin by installing the ''Right Cover'' onto the ''System Control Box''.</li>
:'''NOTE:''' Ensure the '''Power Button cable''' is connected to the ''System Control Box'' Power cable before securing the ''Cover''.
<li>After connecting the '''Power Button''' cable, ensure the ''Right Cover'' is properly aligned with the ''System Control Box''; then secure it with the 12 provided screws (KM3x6mm).</li>
<div class="res-img">[[File:LD_Wall_Mounting_Right_Cover.svg|420px]]</div>
<li>Repeat the above steps for the ''Middle'' and ''Left Cover''.
<div class="res-img">[[File:LD_Wall_Mounting_All_Covers_Yes_LED.svg|420px]]</div>
<li>Your display is now ready for use.</li>
:<div class="res-img">[[File:LD_Front_Panel.svg|375px]]</div></ol>
<noinclude>


{{#seo:
|title=ViewSonic Direct View LED Display
|title_mode=append
|keywords=LD108-121, Direct View LED, Installation, Wall, Floor, Trolly, trolley, how to, install
|description=How to install the LD108-121 Direct View LED display. 
}}

[[Category:LD108-121]]