View source for tc:LD216-251 Wall Installation

<noinclude>  {{DISPLAYTITLE:LD216-251 壁掛}}
{{Sticky_Menu_DirectView_Short_TCH
|1=LD216-251_Introduction
|2=LD216-251_Remote_Control
|3=LD216-251_Wall_Installation
|4=LD216-251_Connecting_Devices
|5=LD216-251_Using_the_Display
|6=LD216-251_On-Screen_Display_Menu
|7=LD216-251_Embedded_Applications
|8=LD216-251_RS-232_Protocol
|9=LD216-251_Specifications
|10=LD216-251_Regulatory_and_Service_Information
}}
{{Top}} </noinclude>
=安裝前=
<ol style="list-style-type:square"><li>請在顯示器背面與任何牆壁之間，保留足夠的氣隙以確保適度通風。</li>
<li>確保沒有來自空調或暖氣通風口的直接氣流吹向顯示器。</li>
<li>避免將顯示器安裝在高濕度場所。</li>
<li>由於功耗高，請務必使用專為本產品而設計的電源線。</li></ol>

=壁掛=

==安裝上下壁掛架==

<ol>
<div class="res-img">[[File:LD216-251_Wall_Mounting_Bracket.svg|550px]]</div>
<li>確保牆壁面積和大小適合安裝。</li>
:'''備註：''' 上壁掛架的離地高度，不得小於 129.92"（3.3 公尺）。

<li>以壁掛架（上圖）為基準，標記八 (8) 個孔並預先鑽孔。</li>

<li>使用隨附的螺絲（M6x50mm 膨脹螺絲用於石材；TA6x30mm 用於承重木材）安裝第一個上壁掛架。</li>

<li>重複步驟 2，確保第二個上壁掛架與第一個上架齊平。</li><br />

<div class="res-img">[[File:LD_Wall_Mounting_After_Upper_Brackets.svg|400px]]</div><br />

<li>安裝下壁掛架，方式與上壁掛架相同。上下壁掛架之間的距離為 103.94" (2640 mm)。</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Spacing.svg|250px]]</div><br />

{{Note-yellow|確保牆壁可安全地支撐 749.57 lbs. (340 kg)。}}
:'''備註：''' 您也可以安裝上壁掛架，懸掛螢幕，然後安裝下壁掛架以便更精準地安裝。

<li>安裝上下壁掛架後，安裝牆應如下所示：</li><br />

<div class="res-img">[[File:LD_Brackets.svg|400px]]</div>
</ol>

==Installing the Middle Cabinets==
<ol>
<li>Ensure the ''Mounting Brackets'' on the rear of the six (6) ''Middle Cabinets'' are positioned at the top and bottom mounting positions as shown below:</li><br />

<div class="res-img">[[File:LD216-251_Rear_Middle_Panels_Separate_Original.svg|400px]]</div><br />

<li>Carefully lift each ''Middle Cabinet'' up onto the Upper ''Wall Mount Brackets''.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_After_Middle_Screens_Update.svg|400px]]</div><br />

<li>Ensure the ''Mounting Brackets'' sit securely on the ''Wall Mount Brackets'' as shown below.</li><br />

<div class="res-img">[[File:LD_Wall_Mount_Close_Up.svg|400px]]</div><br />

<li>Push each ''Locking Bolt'' and lock each ''Hook'' with the hex tool to securely connect each cabinet together.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Connecting_Middle_Screens.png|500px]]</div><br />

:'''NOTE:''' There are eight (8) Locking Bolts and 16 Hooks between each cabinet.

<li>Lift the remaining ''Middle Cabinets'' up onto the Upper ''Wall Mount Brackets'', ensuring the ''Mounting Brackets'' sit securely on the ''Wall Mount Brackets''.</li>

<li>Repeat '''Step 4''', securing the cabinets together with each ''Locking Bolt'' and ''Hook''.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_After_Middle_Screens.svg|400px]]</div>
</ol>

==Installing the Left and Right Cabinet==
<ol>
<li>Ensure the ''Mounting Brackets'' on the rear of the ''Left'' and ''Right Cabinet'' are positioned at the top and bottom mounting positions as shown below:</li> <br />

<div class="res-img">[[File:LD216-251_Rear_Left_and_Right.svg|250px]]</div><br />

<li>Carefully lift the ''Left'' and ''Right Cabinet'' up onto the Upper ''Wall Mount Brackets'', ensuring the ''Mounting Brackets'' sit securely on the ''Wall Mount Brackets''.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_After_All_Screens.svg|400px]]</div><br />

<li>If necessary, adjust the ''Left'' or ''Right Cabinet'' so that they fit seamlessly with the ''Middle Cabinets''.</li>

<li>Push each ''Locking Bolt'' and lock each ''Hook'' with the hex tool to securely connect the ''Left'' and ''Right Cabinets''.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Locking_Bolts.png|400px]]</div>

:'''NOTE:''' There are eight (8) ''Locking Bolts'' and 16 Hooks between each cabinet.
</ol>

==Connecting the System Control Box==
<ol>
<li>Carefully unfold the ''System Control Box'' panel. Ensure the main system control board is on the left.</li>

:'''NOTE:''' Use caution as the ''System Control Box'' panel will be separated into two pieces, however the wires are connected.

<li>Align the holes of the ''Cabinet'' with the ''System Control Box'' to attach.</li><br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Connecting_Box.svg|400px]]</div><br />

<li>Further secure the ''System Control Box'' to the ''Cabinets'' with the 32 provided screws (M6x16mm).</li><br />

<div class="res-img">[[File:LD_Box_Install.png|300px]]</div><br />

<li>Connect the Network and Power cables of the ''Cabinets'' to the ''System Control Box''.</li>

:'''NOTE:''' There are four (4) Network and eight (8) Power cables to connect.
<br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Connecting_Net_Pow.svg|400px]]</div>
</ol>

==Installing the LED Modules==
Install each ''LED Module'' onto the ''Cabinets'', being sure to match the corresponding numbers on the ''Module'' to the ''Cabinet''.

{{Note-yellow|Please wear Anti-Static Gloves before installing the LED modules.}}<br />

<div class="res-img">[[File:LD216-251_Wall_Mounting_Modules_1.svg|450px]]</div>

Ensure each ''Module'' is flush and that there is little to no gap between each.

<div class="res-img">[[File:LD163-181_Wall_Mounting_Modules_No_Cover.png|450px]]</div>

==Installing System Control Box Covers==
There are three (3) System Control Box Covers: Left, Middle, and Right.

<div class="res-img">[[File:LD_Control_Box_Covers.svg|600px]]</div>

<ol>
<li>Begin by installing the ''Right Cover'' onto the ''System Control Box''.</li>
:'''NOTE:''' Ensure the '''Power Button cable''' is connected to the ''System Control Box'' Power cable before securing the ''Cover''.
<li>After connecting the '''Power Button''' cable, ensure the ''Right Cover'' is properly aligned with the ''System Control Box''; then secure it with the 18 provided screws (KM3x6mm).</li>
<div class="res-img">[[File:LD_Wall_Mounting_Right_Cover.svg|420px]]</div>
<li>Repeat the above steps for the ''Middle'' and ''Left Cover''.
<div class="res-img">[[File:LD_Wall_Mounting_All_Covers_Yes_LED.svg|420px]]</div>
<li>Your display is now ready for use.</li>
<div class="res-img">[[File:LD_Front_Panel.svg|400px]]</div>
</ol>
<noinclude>
=Video Overview=
<youtube>yn54zbXpTAA</youtube>
</noinclude>

{{#seo:
|title=ViewSonic 直視型 LED 顯示器
|title_mode=append
|keywords=LD216-251, 直視型 LED 顯示器, 壁掛
|description=LD216-251 壁掛.
}}

[[Category:LD216-251]]