VB-STND-008 ViewSonic Trolley Stand

    From ViewSonic User Guide Database

    Print Icon.svg

    Package Contents

    VB-STND-008 Package Contents.svg
    Letter Quantity Description Note
    A 2 Bolts M6 x 14mm
    B 6 Nuts M8
    C 4 Bolts M5 x 25mm
    D 4 Bolts M6 x 25mm
    E 4 Bolts M8 x 25mm
    F 4 Bolts M4 x 8mm
    G 1 Hex Tool 4mm
    H 1 Wrench
    I 4 Caster Covers Left Covers (x2)
    Right Covers (x2)
    J 2 Attachable Cord Clamps
    K 1 Control Pad
    L 1 USB Type A to
    USB Type A cable
    M 2 Trolley Bases
    N 2 Mounting Brackets
    O 1 Power Extension Cord
    P 1 Power Cord
    Q 1 Keyboard Tray
    NOTE: The power cord included in your package may vary depending on your country. Please contact your local reseller for more information.

    Product Overview

    Front and Side View

    I/O Ports and Controls

    VB-STND-008 IO Ports.png
    Number Port Description
    1 USB A [1] USB A Port
    2 Lift Up/Down, Tilt Up/Down Buttons Adjust Lift Height and Tilt Angle
    3 RJ45 [2] RJ45 Port
    4 AC Out Power Output Socket
    5 AC In Power Input Socket
    1. Only use the USB-A port to connect with an IFP. Lift can be controlled via the application on the IFP.
    2. Only use the RJ45 port to connect with the Control Pad.

    Control Pad

    Control Pad

    Assembling the Product

    Step 1 - Connect the Trolley Body and Base

    1. Prepare the following items:
    Vb-STND-007 Initial Setup 1.PNGVb-STND-007 Initial Setup 2.PNG
    1. Align the three holes on the Trolley Base (M) to the bolts underneath the Trolley Body. Using the wrench (H), secure the Trolley Base to the Trolley Body with the nuts (B).
    Vb-STND-007 Initial Setup 3.PNG
    1. Ensure all nuts are tightened properly on the assembled Trolley Cart.
    Vb-STND-007 Initial Setup 4.PNGVb-STND-007 Initial Setup 5.PNG

    Step 2 - Attach the Mounting Brackets to the IFP

    Attach the Mounting Brackets (N) to the IFP. Depending on the size of the IFP, use either M5 (C), M6 (D), or M8 (E) bolts. Refer to the IFP user guide to find the right bolt size.

    Vb-STND-007 Initial Setup 6.PNG

    Step 3 - Attach the Keyboard Tray

    Attach the Keyboard Tray (Q) to the middle support.

    Vb-STND-007 Initial Setup 7.PNG

    Step 4 - Secure the IFP to the Trolley Cart

    1. Lift the IFP up and hook the Mounting Brackets onto the Trolley Cart.
    NOTE: It is recommended to perform this step with two or more people to avoid personal injury and/or damage to the IFP and Trolley Cart.
    Vb-STND-007 Initial Setup 8.PNG
    1. Secure the Mounting Brackets to the Trolley Cart with two M6 x 14mm bolts (A).
    Vb-STND-007 Initial Setup 9.PNG

    Step 5 - Removing the Protective Cover and Installing a Chrome Box

    1. Unscrew the M4 x 8mm bolts (F) and remove the Protective Cover from the Trolley Cart. Attach the Chrome Box onto the Trolley Cart.
    NOTE: This product does not include an Chrome Box.
    Protective Cover
    Vb-STND-007 Initial Setup 11.PNG
    1. Reattach the Protective Cover onto the Trolley Cart with the M4 x 8mm bolts, covering the Chrome Box.
    Vb-STND-007 Initial Setup 12.PNG
    1. Ensure all parts are accurately and securely held together, as shown in the diagrams below.
    Vb-STND-007 Initial Setup 13.PNG
    Vb-STND-007 Initial Setup 14.PNG

    Step 6 - Move and Park the Trolley Cart

    After moving the Trolley Cart to desired location, push down on the wheel brakes to lock the Trolley Cart in place.

    Vb-STND-007 Initial Setup 15.PNG

    Step 7 - Install the Caster Covers

    Install the Caster Covers (I) to further secure the Trolley Cart in place.

    NOTE: It is recommended to install the Caster Covers to avoid personal injury and/or damage to the IFP and Trolley Cart.
    1. Ensure the wheels are aligned with the Trolley Cart.
    Vb-STND-007 Initial Setup 16.PNG
    1. Slide the Caster Covers over the wheels.
    NOTE: The Caster Covers automatically locks the wheel brakes.
    Vb-STND-007 Initial Setup 17.PNG

    Storing the Caster Covers

    The Caster Covers are magnetic. Refer to the diagram below for the position of the magnet.

    Vb-STND-007 Initial Setup 18.PNG

    When moving the Trolley Cart, attach the Caster Covers to the left and right supports.

    Vb-STND-007 Initial Setup 19.PNG

    Connecting to Power

    1. Connect the power cord to the Trolley Cart.
    2. Plug the power cord plug into a power outlet.
    3. VB-STND-007 Connect Power 1.png
      VB-STND-008 Power Cord.png
    4. Use the cord clamp to secure the cords in place.
    5. VB-STND-008 Connect Power 2.png

    Connecting to the Control Pad

    Connect the Control Pad to the Trolley Cart via the RJ45 Port.

    NOTE: The Control Pad has a magnet on the back. The Control Pad can be attached to any metal surface on the Trolley Cart. Make sure the attached area does not obstruct the Lift functions.
    VB-STND-008 Connect Control Pad.png

    Connecting to the IFP

    1. Connect the IFP to the AC power output of the Trolley Cart.
    2. Connect the USB Type A cord to both the IFP and the Trolley Cart.
    VB-STND-008 Connect IFP.png


    This section will introduce how to adjust the height and angle of the Trolley Cart by using the Lift/Tilt function.
    There are three ways to control the Lift:

    • Using the Trolley Cart Control Panel.
    • Using the Control Pad.
    • Using the Application on the IFP.

    Using the Trolley Cart Control Panel or Control Pad

    VB-STND-008 Using Trolley Pad.png
    Item Icon Description
    Lift Up
    VB-STND-007 Lift Icon Up.svg
    Press and hold to raise the VB-STND-008.
    Lift Down
    VB-STND-007 Lift Icon Down.svg
    Press and hold to lower the VB-STND-008.
    Tilt Up
    VB-STND-008 Lift Icon Tilt Up.svg
    Press and hold to tilt the VB-STND-008 backwards.
    Tilt Down
    VB-STND-008 Lift Icon Tilt Down.svg
    Press and hold to tilt the VB-STND-008 forwards.

    Using the Application on the IFP

    1. Select the More Options Icon (...) from the side tool bar.
    2. VB-STND-007 App Control 1.png
    3. Select Trolley Cart Control.
    4. VB-STND-007 App Control 2.png
    5. Adjust the height of the Trolley Cart accordingly.
    6. VB-STND-008 App Control 3.png
    Item Icon Description
    Lift Up
    VB-STND-007 App Lift Icon Up.svg
    Press and hold to raise the VB-STND-008.
    Lift Down
    VB-STND-007 App Lift Icon Down.svg
    Press and hold to lower the VB-STND-008.
    Tilt Down
    VB-STND-008 App Lift Icon Tilt Down.svg
    Press and hold to tilt the VB-STND-008 forwards.
    Tilt Up
    VB-STND-008 App Lift Icon Tilt Up.svg
    Press and hold to tilt the VB-STND-008 backwards.
    Preset Position 1
    VB-STND-007 App Preset Icon 1.svg
    Adjust the Lift to desired height. Long press to save current height as Preset Position 1.
    Preset Position 2
    VB-STND-007 App Preset Icon 2.svg
    Adjust the Lift to desired height. Long press to save current height as Preset Position 2.
    Preset Position 3
    VB-STND-007 App Preset Icon 3.svg
    Adjust the Lift to desired height. Long press to save current height as Preset Position 3.
    VB-STND-007 App Stop Icon.svg
    When using the Preset Position function, the Lift will adjust to the saved height. If you want to stop this process, press to stop height adjustment and motor movement.

    Technical Specifications

    Item Specifications
    Model No. VS18670
    P/N VB-STND-008
    Swivel 360° by 4” silent wheel
    Height Adjust Range 560 mm (22.05 in)
    Wall Mount Pattern 800 x 600 mm max.
    Material Aluminum Alloy, Plastic, Steel
    Wall Mount Loading 75 kg max. (165 lbs max.)
    Keyboard Tray Loading 10 kg max. (22 lbs max.)
    Input Voltage AC 100v ~ 240v 50/60Hz 10A
    Output Voltage (for IFP Power) AC 100v ~ 240v 50/60Hz 6A
    Control Panel Trolley Cart: Lift Up/Down, Tilt Up/Down
    Control Pad: Lift Up/Down, Tilt Up/Down
    IFP App: Lift Up/Down, Tilt Up/Down, Preset Position 1~3, Stop
    (W x H x D)
    1248.9 x (1330.7 ~ 1890.7) x 706 mm
    (49.17 x (52.4 ~ 74.44) x 28.19 in)
    Weight 65 kg (143 lb)
    Motor Speed 33 mm/second (1.3 in/second)
    Lift Safety Sensor 11 ~ 15 kg (24.25 ~ 33.07 lbs)
    Tilt Angle 0° ~ 90°

    Compliance Information

    This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

    FCC Compliance Statement

    This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

    These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.

    Industry Canada Statement

    CAN ICES-003(B) / NMB-003(B)

    CE Conformity for European Countries

    The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

    The following information is only for EU-member states:

    The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.
    WEEE Logo.gif

    Declaration of RoHS2 Compliance

    This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

    Substance Proposed Maximum Concentration Actual Concentration
    Lead (Pb) 0.1% < 0.1%
    Mercury (Hg) 0.1% < 0.1%
    Cadmium (Cd) 0.01% < 0.01%
    Hexavalent Chromium (Cr6⁺) 0.1% < 0.1%
    Polybrominated biphenyls (PBB) 0.1% < 0.1%
    Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
    Bis (2-ethylhexyl) phthalate (DEHP) 0.1% < 0.1%
    Butyl benzyl phthalate (BBP) 0.1% < 0.1%
    Dibutyl phthalate (DBP) 0.1% < 0.1%
    Diisobutyl phthalate (DIBP) 0.1% < 0.1%

    Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below. Examples of exempted components are:

    • Copper alloy containing up to 4% lead by weight.
    • Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
    • Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
    • Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.

    Indian Restriction of Hazardous Substances

    Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

    Product Disposal at End of Product Life

    ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

    USA & Canada



    For EU users, please contact us for any safety/accident issue experienced with this product:

    Icon Address.svg
    ViewSonic Europe Limited
    Haaksbergweg 75
    1101 BR Amsterdam
    Icon Phone.svg
    +31 (0) 650608655
    Icon Email.svg
    Icon URL.svg

    Copyright Information

    Copyright© ViewSonic® Corporation, 2022. All rights reserved.

    Macintosh and Power Macintosh are registered trademarks of Apple Inc.

    Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

    ViewSonic® and the three birds logo are registered trademarks of ViewSonic® Corporation.

    VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.

    Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

    In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

    No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.


    Using the ViewBoard Stand Safely

    Please read the following Safety Precautions before you start using the device.

    • Keep this user guide in a safe place for later reference.
    • Read all warnings and follow all instructions.
    • To prevent damage, avoid any physical pressure, vibration, or immersion during transportation, possession, or installation of the product.
    • Always place the product on a flat, stable surface.
    • Avoid contacting any liquids, gas, or corrosive materials with the shell of the product.
    • This product has no parts which can be repaired by the user. Any damage caused by the user's own disassembly is not covered by warranty.
    • This product is special use with ViewSonic® commercial Touch Display only, Use with other model is capable of resulting in instability causing possible injury.
    • This product is only compatible with panels up to a maximum size of 86”.
    • The maximum weight loading of this product is 75 kgs (165 lbs).
    • Avoid the following to prevent the personal injury and/or equipment damage:
    • Children MUST NOT operate plant or machinery.
    • KEEP AWAY from moving parts to avoid injury.
    • DO NOT move the cart with the lift in the highest position.
    • DO NOT push the cart from the front or attempt to lift it.
    • DO NOT move the cart by pushing on the IFP/panel.
    • DO NOT move the cart over cords or uneven, dirty, and/or slopes.
    VB-STND Safety Precaution.png

    Troubleshooting Common Problems

    This section describes some common problems that you may experience when using the Trolley Cart.

    Problem or Issue Possible Solutions
    No power
    • Plug another electrical device into the power outlet to verify that the outlet is supplying power.
    • Ensure the power cord is properly and securely connected to the device and power outlet.
    • If the Trolley Cart works but not the IFP, ensure the power cords are properly and securely connected to the IFP and the Trolley Cart.
    Lift is not moving
    • Via Trolley Cart:
    Ensure the power cord is connect properly.
    Ensure the outlet is supplying power.
    • Via Control Pad:
    Ensure the Control Pad Cable is properly and securely connected to the Trolley Cart.
    • Via app on IFP:
    Ensure the USB cable is properly and securely connected to the Trolly Cart and IFP.

    Customer Service Contact Information

    For technical support or product service, see the table below or contact your reseller.

    You will need the product's serial number

    Asia Pacific & Africa

    Country / Region Website
    Australia https://viewsonic.com/au/
    Bangladesh https://www.viewsonic.com/bd/
    中囯(China) https://www.viewsonic.com.cn
    香港 (繁體中文) https://www.viewsonic.com/hk/
    Hong Kong (English) https://www.viewsonic.com/hk-en/
    India https://www.viewsonic.com/in/
    Indonesia https://www.viewsonic.com/id/
    Israel https://www.viewsonic.com/il/
    日本 (Japan) https://www.viewsonic.com/jp/
    Korea https://www.viewsonic.com/kr/
    Malaysia https://www.viewsonic.com/my/
    Middle East https://www.viewsonic.com/me/
    Myanmar https://www.viewsonic.com/mm/
    Nepal https://www.viewsonic.com/np/
    New Zealand https://www.viewsonic.com/nz/
    Pakistan https://www.viewsonic.com/pk/
    Philippines https://www.viewsonic.com/ph/
    Singapore https://www.viewsonic.com/sg/
    臺灣 (Taiwan) https://www.viewsonic.com/tw/
    ประเทศไทย (Thailand) https://www.viewsonic.com/th/
    Việt Nam https://www.viewsonic.com/vn/
    South Africa & Mauritius https://www.viewsonic.com/za/


    Country / Region Website
    United States https://www.viewsonic.com/us/
    Canada https://www.viewsonic.com/us/
    Latin America https://www.viewsonic.com/la/


    Country / Region Website
    Europe https://www.viewsonic.com/eu/
    France https://www.viewsonic.com/fr/
    Deutschland https://www.viewsonic.com/de/
    Қазақстан https://www.viewsonic.com/kz/
    Россия https://www.viewsonic.com/ru/
    España https://www.viewsonic.com/es/
    Türkiye https://www.viewsonic.com/tr/
    Україна https://www.viewsonic.com/ua/
    United Kingdom https://www.viewsonic.com/uk/